SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P034031

DTC Code DTC Name
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal

DESCRIPTION

Refer to DTC P034011.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal No camshaft position sensor (for intake camshaft) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).

  • Open or short in camshaft position sensor (for intake camshaft) circuit

  • Camshaft position sensor (for intake camshaft)

  • Intake camshaft

  • ECM

 Comes on DTC stored SAE Code: P0340

Reference: Inspection using an oscilloscope.

Click here

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for intake camshaft) despite the camshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor (for intake camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Start the engine.

  7. Idle the engine for 10 seconds or more [A].

  8. Turn the GTS on.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [B].

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P034031.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE, perform steps [A] through [B] again.

WIRING DIAGRAM

Refer to DTC P034011.

Click here

CAUTION / NOTICE / HINT

Tech Tips


  • If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

  • Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR

    B006ZSNC03
    *a

    Front view of wire harness connector

    (to Camshaft Position Sensor (for Intake Camshaft))

    Tech Tips

    Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


    1. Disconnect the camshaft position sensor (for intake camshaft) connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      C18-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
      C18-1 (VVI+) - Body ground Engine switch on (IG) 3.0 to 5.0 V

    4. Turn the engine switch off and wait for at least 30 seconds.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C18-3 (VC) - C18-1 (VVI+) Engine switch off 1.425 to 1.575 kΩ
      C18-2 (VVI-) - Body ground Engine switch off Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM) Click here

    OK

  2. CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

    B0070QFC01
    *a Clearance

    1. Visually check the camshaft position sensor (for intake camshaft) for damage.

    2. Check the camshaft position sensor (for intake camshaft) installation condition.

      OK
      The camshaft position sensor (for intake camshaft) does not have any damage and is installed properly.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) Click here

    OK

  3. INSPECT INTAKE CAMSHAFT (TIMING ROTOR)


    1. Check the timing rotor of the intake camshaft.

      OK
      Camshaft timing rotor does not have any cracks or deformation.

      Tech Tips

      Perform "Inspection After Repair" after replacing the intake camshaft.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) Click here

    NG

    REPLACE INTAKE CAMSHAFT Click here

  4. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)


    1. Disconnect the camshaft position sensor (for intake camshaft) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C18-1 (VVI+) - C57-90 (VV1+) Always Below 1 Ω
      C18-2 (VVI-) - C57-89 (VV1-) Always Below 1 Ω
      C18-3 (VC) - C57-88 (VCV1) Always Below 1 Ω
      C18-1 (VVI+) or C57-90 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
      C18-2 (VVI-) or C57-89 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
      C18-3 (VC) or C57-88 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR