UB80E AUTOMATIC TRANSAXLE FLUID REPLACEMENT

PROCEDURE


  1. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

    Click here

  2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

    Click here

  3. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  5. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  6. REPLACE AUTOMATIC TRANSAXLE FLUID


    1. Lift the vehicle. [#1]

      Note

      Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).

    2. B006ZGQ

      Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2]

    3. B006ZAU

      Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. [#3]

    4. B007036C01
      *1 No. 1 Transmission Oil Filler Tube

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. [#4]

    5. B0070TT

      Measure the amount of automatic transaxle fluid drained. [#5]

      Tech Tips

      Add the same amount of automatic transaxle fluid in step [#8].

    6. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing. [#6]

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }
    7. B006ZAU

      Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing. [#7]

      Tech Tips

      Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

    8. B00700L

      Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]

      Note

      Use Toyota Genuine ATF WS.

    9. B006ZGQ

      Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]

      Tech Tips

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

    10. Lower the vehicle. [#10]

    11. Start the engine. [#11]

    12. Slowly move the shift lever from P to D, and then back to P. [#12]

      Tech Tips


      • Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

      • Keep the shift lever in each position for approximately 3 seconds.

    13. Allow the engine to idle for 30 seconds to warm it up. [#13]

    14. Turn the engine switch off. [#14]

    15. Repeat steps [#1] to [#14].

    16. Repeat steps [#1] to [#10].

  7. ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

    Click here

  8. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

    Click here

  9. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

    Click here

  10. ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL

    Click here

  11. REBUILD WORK

    Click here

  12. INSTALL FRONT FENDER APRON SEAL LH

    Click here

  13. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  14. INSTALL NO. 1 ENGINE UNDER COVER

    Click here

  15. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

    Click here

  16. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

    Click here