Click here

AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P271314

Click here
Click here
DTC Code DTC Name
P271314 Pressure Control Solenoid "D" Circuit Short to Ground or Open
Click here

DESCRIPTION

Refer to DTC P27137F.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P271314 Pressure Control Solenoid "D" Circuit Short to Ground or Open While the engine is running, a short to ground or open is detected in the solenoid (SLT) valve circuit for 1 second (1-trip detection logic).

  • Solenoid (SLT) valve

  • Transmission wire

  • Harness and connector

  • ECM

 Comes on DTC stored

SAE Code:

P2720
Click here

MONITOR DESCRIPTION

When an open or short to ground in the solenoid (SLT) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

Click here

CONFIRMATION DRIVING PATTERN

Tip:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for 2 minutes or more.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine.

  7. Wait for 2 seconds or more with the engine running.

  8. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

  9. Input the DTC: P271314.

  10. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

Click here

WIRING DIAGRAM

Refer to DTC P271312.

Click here

Click here

CAUTION / NOTICE / HINT

Note:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLT) VALVE) - ECM)


    1. Disconnect the C59 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C59-10 (SLT+) - C59-9 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      C59-10 (SLT+) or C59-9 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

  2. Click here

    REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

  3. Click here

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the C93 transmission wire connector.

    2. Disconnect the C59 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C93-24 (SLT+) - C59-10 (SLT+) Always Below 1 Ω
      C93-23 (SLT-) - C59-9 (SLT-) Always Below 1 Ω
      C93-24 (SLT+) or C59-10 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
      C93-23 (SLT-) or C59-9 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

  4. Click here

    INSPECT SOLENOID (SLT) VALVE


    1. B0071RQC76
      *a

      Component without harness connected

      (Solenoid (SLT) Valve)

      Remove the solenoid (SLT) valve.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Solenoid (SLT) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG