DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE) Distance Control Switch Circuit

DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

B006YMZE06

CAUTION / NOTICE / HINT

Note


  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

  • If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

    Click here

  • Before replacing the ECM, refer to Service Bulletin.

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Radar Cruise 2 / Data List.

    5. Read the Data List according to the display on the GTS.


      Powertrain > Radar Cruise2 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Distance Control Switch Distance control switch signal ON or OFF

      ON: Distance control switch on

      OFF: Distance control switch off

      		 -

      Powertrain > Radar Cruise2 > Data List
      Tester Display
      Distance Control Switch
      OK
      When the vehicle-to-vehicle distance control switch is operated, the display changes as shown above.
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Remove the steering pad switch assembly.

      Click here

    2. Inspect the steering pad switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  3. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Remove the spiral cable sub-assembly.

      Click here

    2. Inspect the spiral cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)


    1. Disconnect the K22 spiral cable sub-assembly connector.

    2. Disconnect the V6 forward recognition camera connector.

    3. Disconnect the A24 ECM connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K22-6 (DIST) - V6-3 (LKSW) Always Below 1 Ω
      K22-2 (ECC) - A24-28 (ECCS) Always Below 1 Ω
      K22-6 (DIST) or V6-3 (LKSW) - Body ground Always 10 kΩ or higher
      K22-2 (ECC) or A24-28 (ECCS) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    1. Disconnect the A24 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A24-10 (E1) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK ECM (ECM TERMINALS)


    1. B006Y1QC01
      *a

      Component without harness connected

      (ECM)

      Disconnect the A24 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A24-28 (ECCS) - A24-10 (E1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FORWARD RECOGNITION CAMERA Click here

    NG

    REPLACE ECM Click here