OIL COOLER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

Replacement of ECM Vehicle Identification Number (VIN) registration MIL comes on

Click here w/ Canister Pump Module

Click here w/o Canister Pump Module
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)

  1. Reset memory*1

  2. Transfer transaxle compensation code

  3. Perform road test to allow ECM to learn

  • Large shift shock

  • Deterioration of fuel efficiency

Click here for UB80E Initialization

Click here for UB80E Registration

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)

  1. Reset memory*1

  2. Reset transaxle compensation code

  3. Perform road test to allow ECM to learn
Replacement of ECM Perform code registration (Immobiliser function)

  • Wireless door lock control system

  • Smart Entry and Start System (for Entry Function)

  • Smart Entry and Start System (for Start Function)

  • Steering lock function

 See Service Bulletin for the registration method.
*1: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE


  1. REMOVE BATTERY

    Click here

  2. REMOVE ECM

    Click here

  3. REMOVE BATTERY CLAMP SUB-ASSEMBLY

    Click here

  4. REMOVE FRONT WHEEL LH

    Click here

  5. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

    Click here

  6. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

    Click here

  7. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  8. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  9. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  10. DRAIN ENGINE COOLANT

    Click here

  11. DRAIN AUTOMATIC TRANSAXLE FLUID

    Click here

  12. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE


    1. B00714D

      Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.

      Tech Tips

      Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.

  13. DISCONNECT INLET NO. 1 OIL COOLER HOSE


    1. B006ZHV

      Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.

      Tech Tips

      Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.

  14. REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE


    1. B0070SO

      Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.

    2. B006ZLW

      Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

      Tech Tips

      Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.

    3. B0070KJ

      Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.

      Tech Tips

      Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.

    4. B006ZRAC01
      *1 No. 1 Oil Cooler Tube Sub-assembly without Hose
      *2 Inlet No. 1 Oil Cooler Hose
      *3 Inlet No. 2 Oil Cooler Hose
      *4 Outlet No. 1 Oil Cooler Hose
      *5 Outlet No. 2 Oil Cooler Hose

      Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.

  15. DISCONNECT NO. 1 WATER BY-PASS HOSE


    1. B0070AL

      Disengage the 3 clamps to remove the transmission breather clamp.

    2. B00704D

      Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

      Tech Tips

      Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.

  16. DISCONNECT WATER BY-PASS HOSE ASSEMBLY


    1. B006ZMT

      Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

      Tech Tips

      Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.

  17. REMOVE TRANSMISSION OIL COOLER


    1. B00706Z

      Remove the 3 bolts.

    2. Disengage the hook to remove the transmission oil cooler from the automatic transaxle case sub-assembly.

      Tech Tips

      Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.