VEHICLE PROXIMITY NOTIFICATION SYSTEM Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible

DESCRIPTION

The vehicle approaching speaker controller communicates with the GTS through the DLC3.

WIRING DIAGRAM

B004F5LE04
*a from IG1 NO. 3 Relay
*b ECU-IG1 NO. 1
*c Instrument Panel Junction Block Assembly
*d Vehicle Approaching Speaker Controller

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

The vehicle approaching speaker controller and GTS communicate using SIL communication.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Health Check.

      Result
      Result Proceed to
      Communication with the vehicle approaching speaker controller is not possible A
      Communication with the vehicle approaching speaker controller is possible B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 3 RELAY)


    1. Disconnect the O33 vehicle approaching speaker controller connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O33-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
      Result
      Result
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 3 RELAY) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O33-7 (GND) - Body ground Always Below 1 Ω
      Result
      Result
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - DLC3)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O33-9 (PRST) - O8-7 (SIL) Always Below 1 Ω
      O33-9 (PRST) or O8-7 (SIL) - Body ground Always 10 kΩ or higher
      Result
      Result
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O8-4 (CG) - Body ground Always Below 1 Ω
      Result
      Result
      OK
      NG

    OK

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 3 RELAY)


    1. Disconnect the 4A instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O33-1 (IG) - 4A-54 Always Below 1 Ω
      O33-1 (IG) or 4A-54 - Body ground Always 10 kΩ or higher
      Result
      Result
      OK
      NG

    OK

    REPAIR INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR