WIPER AND WASHER SYSTEM TERMINALS OF ECU


  1. CHECK WINDSHIELD WIPER SWITCH ASSEMBLY

    A01OB77N03

    1. Disconnect the O23 and O24 windshield wiper switch assembly connectors.

    2. Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

      Terminal No.

      (Symbol)

      		 Wiring Color Terminal Description Condition Specified Condition
      O23-2 (+B) - Body ground R - Body ground Power switch on (IG) signal (Power source circuit) Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V
      O23-3 (TAIL) - Body ground*1 LG - Body ground Headlight dimmer switch position signal Power switch on (IG), light control switch in tail or head position Below 1 V
      Power switch on (IG), light control switch not in tail or head position 11 to 14 V
      O23-4 (RLY2) - Body ground R - Body ground INT relay operation signal Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V
      O23-5 (RLY1) - Body ground B - Body ground WIPER relay operation signal Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V
      O23-7 (E) - Body ground BR - Body ground Ground Always Below 1 Ω
      O24-4 (EW) - Body ground*2 W-B - Body ground Ground Always Below 1 Ω
      O24-7 (EW) - Body ground*3 W-B - Body ground Ground Always Below 1 Ω

      • *1: w/ Auto Wiper System

      • *2: for Wiper Switch RH Side Type

      • *3: for Wiper Switch LH Side Type

      Tech Tips

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the O23 and O24 windshield wiper switch assembly connectors.

    4. Measure the voltage and check for pulses according to the value(s) in the table below.

      Terminal No.

      (Symbol)

      		 Wiring Color Terminal Description Condition Specified Condition
      O23-3 (TAIL) - Body ground*1 LG - Body ground Headlight dimmer switch position signal Power switch on (IG), headlight dimmer switch in off position 11 to 14 V
      Power switch on (IG), headlight dimmer switch in on position Below 1 V
      O23-4 (RLY2) - Body ground R - Body ground INT relay operation signal Power switch on (IG), wiper switch off 11 to 14 V
      Power switch on (IG), wiper switch in LO position Below 1 V
      O23-5 (RLY1) - Body ground B - Body ground WIPER relay operation signal Power switch on (IG), wiper switch off 11 to 14 V
      Power switch on (IG), wiper switch in HI position Below 1 V
      O23-8 (MPX1) - Body ground*1 G - Body ground LIN communication signal Power switch on (IG) Pulse generation
      O23-10 (CSS+) - O23-9 (CSS-) R - L Vehicle speed signal Power switch on (IG), wheel being rotated Pulse generation
      O23-20 (+S) - Body ground G - Body ground Wiper motor operation signal Power switch on (IG), wiper switch off (Wiper blades are at stop (park) position) Below 1 V
      Power switch on (IG), wiper switch in LO or HI position 11 to 14 V
      O24-4 (WF) - Body ground*2 R - Body ground Washer motor operation signal Power switch on (IG), washer switch off 11 to 14 V
      Power switch on (IG), washer switch on Below 1 V
      O24-7 (WF) - Body ground*3 R - Body ground Washer motor operation signal Power switch on (IG), washer switch off 11 to 14 V
      Power switch on (IG), washer switch on Below 1 V

      • *1: w/ Auto Wiper System

      • *2: for Wiper Switch LH Side Type

      • *3: for Wiper Switch RH Side Type

      Tech Tips

      If the result is not as specified, the windshield wiper switch assembly may be malfunctioning.

  2. CHECK HEADLIGHT CLEANER CONTROL RELAY (w/ Headlight Cleaner System)

    A01OAH9N07

    1. Disconnect the A44 headlight cleaner control relay connector.

    2. Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

      Tech Tips

      The voltage cannot be measured with the connector connected to the headlight cleaner control relay as the connector is watertight.

      Terminal No.

      (Symbol)

      		 Wiring Color Terminal Description Condition Specified Condition
      A44-3 (IG) - Body ground B - Body ground Power switch on (IG) signal (Power source circuit) Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V
      A44-4 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
      A44-6 (PB) - Body ground W - Body ground Headlight cleaner motor operation signal Always 11 to 14 V

      Tech Tips

      If the result is not as specified, there may be a malfunction in the wire harness.

  3. CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for Single Beam Headlight with Headlight Cleaner System)


    1. Measure the voltage according to the value(s) in the table below.

      A01WXFUN34

      Terminal No.

      (Symbol)

      		 Wiring Color Terminal Description Condition Specified Condition
      A61-4 (FRWA) - Body ground R - Body ground Washer switch operation signal Power switch on (IG), washer switch off 11 to 14 V
      Power switch on (IG), washer switch on Below 1 V
      A61-16 (HLC) - Body ground R - Body ground Headlight cleaner operation signal Power switch on (IG), headlight cleaner not operating 11 to 14 V
      Power switch on (IG), headlight cleaner operating Below 1 V

      Tech Tips

      If the result is not as specified, the headlight leveling ECU assembly may be malfunctioning.

  4. HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY RH (for Triple Beam Headlight with Headlight Cleaner System)


    1. Measure the voltage according to the value(s) in the table below.

      A01ODKVN03

      Tech Tips

      The voltage cannot be measured with the connector connected to the headlight light control ECU sub-assembly RH as the connector is watertight.

      Terminal No.

      (Symbol)

      		 Wiring Color Terminal Description Condition Specified Condition
      A7-7 (HLC) - Body ground R - Body ground Headlight cleaner operation signal Power switch on (IG), headlight cleaner not operating 11 to 14 V
      Power switch on (IG), headlight cleaner operating Below 1 V
      A7-18 (FRWA) - Body ground R - Body ground Washer switch operation signal Power switch on (IG), washer switch off 11 to 14 V
      Power switch on (IG), washer switch on Below 1 V

      Tech Tips

      If the result is not as specified, the headlight light control ECU sub-assembly RH may be malfunctioning.