AIRBAG SYSTEM, Diagnostic DTC:B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, B1697/82, B1698/82

DTC Code DTC Name
B1627/82 Lost communication with Side Airbag Sensor LH
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
B1637/82 Lost Communication with Rear Airbag Sensor LH
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
B1647/82 Lost Communication with Side Satellite Sensor Bus LH
B1697/82 Lost Communication with Door Side Airbag Sensor LH
B1698/82 Door Side Airbag Sensor LH Initialization Incomplete

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) consists of the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH.

The side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1627/82 Lost communication with Side Airbag Sensor LH

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode
B1637/82 Lost Communication with Rear Airbag Sensor LH

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode
B1647/82 Lost Communication with Side Satellite Sensor Bus LH

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode
B1697/82 Lost Communication with Door Side Airbag Sensor LH

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode
B1698/82 Door Side Airbag Sensor LH Initialization Incomplete

  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Rear airbag sensor LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag ECU assembly malfunction

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Rear airbag sensor LH

  • Door side airbag sensor LH

  • Airbag ECU assembly

 Does not apply to test/check mode

WIRING DIAGRAM

B004FDSE38
*a Rear Airbag Sensor LH
*b Door Side Airbag Sensor LH
*c Side Airbag Sensor Assembly LH
*d Airbag ECU Assembly

CAUTION / NOTICE / HINT

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE


  1. CHECK CURRENT DTC


    1. Check for current DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips


      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

      • Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1697, B1698 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      Current DTC B1647 or 82 is output. A
      Current DTC B1638 is output. B
      Current DTC B1628 is output. C
      Current DTC B1697 or B1698 is output. D
      Current DTC B1637 is output. E
      Current DTC B1627 is output. F
      Current DTCs B1627, B1628, B1637, B1638, B1647, B1697, B1698 and 82 are not output. G

    B

    CHECK HISTORY DTC Click here

    C

    CHECK HISTORY DTC Click here

    D

    CHECK CONNECTORS Click here

    E

    CHECK REAR AIRBAG SENSOR LH Click here

    F

    CHECK SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    G

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the No. 2 floor wire and front door wire LH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the No. 2 floor wire and front door wire LH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  3. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. B004GJDC05
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag ECU Assembly)
      *b

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Using a service wire, connect terminals 17 (BBL+) and 18 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - U17-3 (BCL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. B004E78C22
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - U17-3 (BCL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  5. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. B004E78C22
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - Body ground Power switch on (IG) Below 1 V
      U17-3 (BCL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  6. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. B004E78C22
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - Body ground Always 1 MΩ or higher
      U17-3 (BCL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  7. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. B004EYVC13
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 4 (BBL+) and 3 (BBL-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - U17-2 (BBL-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  8. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. B004G4OC44
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - U17-2 (BBL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  9. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. B004G4OC44
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - Body ground Power switch on (IG) Below 1 V
      U17-2 (BBL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  10. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. B004G4OC44
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - Body ground Always 1 MΩ or higher
      U17-2 (BBL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  11. CHECK WIRE HARNESS (OPEN)


    1. B004EB8C08
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Connect the connectors that link the No. 2 floor wire and front door wire LH.

    2. Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - S11-1 (BDL-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (OPEN) Click here

    OK

  12. CHECK WIRE HARNESS (SHORT)


    1. B004GN5C04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - S11-1 (BDL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT) Click here

    OK

  13. CHECK WIRE HARNESS (SHORT TO B+)


    1. B004GN5C04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
      S11-1 (BDL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+) Click here

    OK

  14. CHECK WIRE HARNESS (SHORT TO GROUND)


    1. B004GN5C04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - Body ground Always 1 MΩ or higher
      S11-1 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) Click here

    OK

  15. CHECK REAR AIRBAG SENSOR LH


    1. B004F97C02
      *1 Rear Airbag Sensor RH
      *2 Airbag ECU Assembly

      Connect the connectors to the side airbag sensor assembly LH, door side airbag sensor LH and airbag ECU assembly.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  16. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B004G65C02
      *1 Side Airbag Sensor Assembly RH
      *2 Rear Airbag Sensor LH

      Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  17. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. B004EE3C02
      *1 Door Side Airbag Sensor RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the door side airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the door side airbag sensor LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  18. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. B004FFWC04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - Body ground Always 1 MΩ or higher
      SU1-36 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  19. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. B004FFWC04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - Body ground Power switch on (IG) Below 1 V
      SU1-36 (BDL-) - Body ground Power switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  20. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. B004FFWC04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - SU1-36 (BDL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  21. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. B004G8ZC06
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

      Tech Tips

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - SU1-36 (BDL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  22. CHECK HISTORY DTC


    1. Check for history DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than history DTC B1637 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      History DTC B1637 is not output. A
      History DTC B1637 is output. B

    B

    CHECK REAR AIRBAG SENSOR LH Click here

    A

  23. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag ECU assembly and rear airbag sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag ECU assembly and rear airbag sensor LH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  24. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. B004GJDC05
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag ECU Assembly)
      *b

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Using a service wire, connect terminals 17 (BBL+) and 18 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - U17-3 (BCL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  25. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. B004E78C22
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - U17-3 (BCL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  26. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. B004E78C22
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - Body ground Power switch on (IG) Below 1 V
      U17-3 (BCL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  27. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. B004E78C22
      *1 Rear Airbag Sensor LH
      *2 Airbag ECU Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-4 (BCL+) - Body ground Always 1 MΩ or higher
      U17-3 (BCL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  28. CHECK REAR AIRBAG SENSOR LH


    1. B004F97C02
      *1 Rear Airbag Sensor RH
      *2 Airbag ECU Assembly

      Connect the connector to the airbag ECU assembly.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1638 is output. A
      DTC B1633 is output. B
      DTCs B1633 and B1638 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  29. CHECK REAR AIRBAG SENSOR LH


    1. B004F97C02
      *1 Rear Airbag Sensor RH
      *2 Airbag ECU Assembly

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the rear airbag sensor LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1637 is output. A
      DTC B1632 is output. B
      DTCs B1632 and B1637 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  30. CHECK HISTORY DTC


    1. Check for history DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than history DTC B1627 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      History DTC B1627 is not output. A
      History DTC B1627 is output. B

    B

    CHECK SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    A

  31. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor assembly LH and rear airbag sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  32. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. B004EYVC13
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 4 (BBL+) and 3 (BBL-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - U17-2 (BBL-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  33. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. B004G4OC44
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - U17-2 (BBL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  34. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. B004G4OC44
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - Body ground Power switch on (IG) Below 1 V
      U17-2 (BBL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  35. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. B004G4OC44
      *1 Side Airbag Sensor Assembly LH
      *2 Rear Airbag Sensor LH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U17-1 (BBL+) - Body ground Always 1 MΩ or higher
      U17-2 (BBL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  36. CHECK REAR AIRBAG SENSOR LH


    1. B004F97C02
      *1 Rear Airbag Sensor RH
      *2 Airbag ECU Assembly

      Connect the connector to the side airbag sensor assembly LH.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1628 is output. A
      DTC B1623 is output. B
      DTCs B1623 and B1628 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  37. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B004G65C02
      *1 Side Airbag Sensor Assembly RH
      *2 Rear Airbag Sensor LH

      Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1628 is output. A
      DTC B1623 is output. B
      DTCs B1623 and B1628 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  38. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B004G65C02
      *1 Side Airbag Sensor Assembly RH
      *2 Rear Airbag Sensor LH

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1627 is output. A
      DTC B1622 is output. B
      DTCs B1622 and B1627 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  39. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the No. 2 floor wire and front door wire LH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the No. 2 floor wire and front door wire LH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  40. CHECK WIRE HARNESS (OPEN)


    1. B004EB8C08
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Connect the connectors that link the No. 2 floor wire and front door wire LH.

    2. Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - S11-1 (BDL-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (OPEN) Click here

    OK

  41. CHECK WIRE HARNESS (SHORT)


    1. B004GN5C04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - S11-1 (BDL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT) Click here

    OK

  42. CHECK WIRE HARNESS (SHORT TO B+)


    1. B004GN5C04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
      S11-1 (BDL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+) Click here

    OK

  43. CHECK WIRE HARNESS (SHORT TO GROUND)


    1. B004GN5C04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S11-2 (BDL+) - Body ground Always 1 MΩ or higher
      S11-1 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) Click here

    OK

  44. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B004G65C02
      *1 Side Airbag Sensor Assembly RH
      *2 Rear Airbag Sensor LH

      Connect the connector to the door side airbag sensor LH.

    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1697 or B1698 is output. A
      DTC B1692 or B1693 is output. B
      DTCs B1692, B1693, B1697 and B1698 are not output. C

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  45. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. B004EE3C02
      *1 Door Side Airbag Sensor RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the door side airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1697 or B1698 is output. A
      DTC B1692 or B1693 is output. B
      DTCs B1692, B1693, B1697 and B1698 are not output. C

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the door side airbag sensor LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  46. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. B004FFWC04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - Body ground Always 1 MΩ or higher
      SU1-36 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  47. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. B004FFWC04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - Body ground Power switch on (IG) Below 1 V
      SU1-36 (BDL-) - Body ground Power switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  48. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. B004FFWC04
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - SU1-36 (BDL-) Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  49. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. B004G8ZC06
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 No. 2 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Front Door Wire LH)

      Disconnect the No. 2 floor wire connector from the front door wire LH.

      Tech Tips

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SU1-35 (BDL+) - SU1-36 (BDL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE

  50. CHECK REAR AIRBAG SENSOR LH


    1. B004F97C02
      *1 Rear Airbag Sensor RH
      *2 Airbag ECU Assembly

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the rear airbag sensor LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1637 is output. A
      DTC B1632 is output. B
      DTCs B1632 and B1637 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE REAR AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

  51. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B004G65C02
      *1 Side Airbag Sensor Assembly RH
      *2 Rear Airbag Sensor LH

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      DTC B1627 is output. A
      DTC B1622 is output. B
      DTCs B1622 and B1627 are not output. C

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    A

    REPLACE AIRBAG ECU ASSEMBLY Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here