REAR LOWER ARM INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY


    1. Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

  2. INSTALL REAR LOWER COIL SPRING INSULATOR

    Click here

  3. INSTALL REAR UPPER COIL SPRING INSULATOR

    Click here

  4. INSTALL REAR COIL SPRING

    Click here

  5. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

    Click here

  6. INSTALL REAR STABILIZER LINK ASSEMBLY

    Click here

  7. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

    2. Temporarily install the rear No. 1 suspension arm assembly to the rear axle assembly with the bolt and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

  8. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY

    Click here

  9. STABILIZE SUSPENSION

    Click here

  10. INSTALL TOE CONTROL LINK SUB-ASSEMBLY

    Click here

  11. INSTALL REAR SHOCK ABSORBER ASSEMBLY

    Click here

  12. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY


    1. Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the bolt.

      Torque:
      150 N*m  { 1530 kgf*cm, 111 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    2. Install the rear No. 2 suspension arm assembly (rear axle assembly side) with the bolt.

      Torque:
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  13. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. Install the rear No. 1 suspension arm assembly (rear suspension member sub-assembly side) with the bolt.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    2. Install the rear No. 1 suspension arm assembly (rear axle assembly side) with the bolt.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  14. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  15. INSTALL REAR SUSPENSION ARM COVER


    1. Install the rear suspension arm cover to the rear No. 2 suspension arm with the 3 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  16. INSTALL REAR WHEEL

    Click here

  17. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  18. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (for Single Beam Headlight)

    Click here

  19. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (for Triple Beam Headlight)

    Click here

  20. ADJUST HEADLIGHT AIMING (for Single Beam Headlight)

    Click here

  21. ADJUST HEADLIGHT AIMING (for Triple Beam Headlight)

    Click here