HYBRID CONTROL SYSTEM, Diagnostic DTC:P0AFC-150

DTC Code DTC Name
P0AFC-150 Hybrid Battery Pack Sensor Module

DESCRIPTION

The hybrid vehicle control ECU assembly alerts the driver and performs fail-safe control based on error signals sent from the battery voltage sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AFC-150 Hybrid Battery Pack Sensor Module

Abnormal battery voltage sensor power source voltage:

Power source voltage of the battery voltage sensor drops during precharge.

(1 trip detection logic)

  • Battery voltage sensor

  • Wire harness or connector

 Comes on

Master Warning Light:

Comes on
Related Data List
DTC No. Data List
P0AFC-150

  • Auxiliary Battery Vol (Battery voltage sensor power source voltage)

  • +B

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AFC-123.

Click here

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the power switch on (READY) and wait for 15 seconds or more.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note


      • Check for and record any DTCs, INF codes and freeze frame data, then disconnect the cable from the negative (-) auxiliary battery terminal.

      • After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper No. 5 HV battery carrier bracket.

      Click here

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the power switch on (IG).

    5. B004GIXC81
      *a

      Component with harness connected

      (Battery Voltage Sensor)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      p1-1 (IGCT) - p1-5 (GND) Power switch on (IG) 11 to 14 V

      Note

      Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    6. Turn the power switch off.

    7. Disconnect the cable from the negative (-) auxiliary battery terminal.

    8. Install the upper No. 5 HV battery carrier bracket.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE BATTERY VOLTAGE SENSOR Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BODY GROUND)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper No. 5 HV battery carrier bracket.

      Click here

    3. B004GIXC82
      *a

      Component with harness connected

      (Battery Voltage Sensor)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      p1-5 (GND) - Body ground Power switch off Below 1 Ω

    4. Install the upper No. 5 HV battery carrier bracket.

      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 5 FUSE - BATTERY VOLTAGE SENSOR)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY VOLTAGE SENSOR - BODY GROUND)