FRONT SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL SEAT ADJUSTER COVER CAP


    1. B004EYR

      Install the 2 seat adjuster cover caps.

  2. INSTALL FRONT SEAT WIRE


    1. Connect each connector and engage each clamp to install the front seat wire.

  3. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY


    1. B004FA0

      Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.

    2. B004EPY

      w/ Climate Control Seat System:


      1. Engage the clamp.

  4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH


    1. Engage the 3 claws to install the front seat cushion edge protector LH.

    2. B004GM5

      Install the screw.

  5. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

    Tech Tips

    Perform the same procedure as for the LH side.

  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. B004GAVN01

      Engage the clip (B) to install the front seat lower cushion shield LH.

    2. Engage the hook as shown in the illustration.

    3. Engage the clip (A).

  7. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. B004E75

      Engage the clip to install the front seat lower cushion shield RH.

    2. Engage the hook as shown in the illustration.

    3. Install the screw.

  8. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)


    1. B004G7J

      Install the seat cushion climate control blower assembly.

    2. B004F8X

      Connect the connector.

  9. INSTALL SEAT CUSHION CLIMATE CONTROL BRACKET (w/ Climate Control Seat System)


    1. B004GC4

      Install the seat cushion climate control bracket to the seat cushion climate control blower assembly with the 2 screws.

  10. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)


    1. B004FJJ

      Engage the 2 claws to install the seat cushion climate control duct to the seat cushion climate control blower assembly.

  11. INSTALL FRONT SEAT CUSHION PAD WITH COVER


    1. Temporarily install the front seat cushion pad with cover.

      Note

      Be careful not to damage the front seat cushion pad with cover.

    2. B004G6M

      Engage the 7 hooks to install the front seat cushion pad with cover.

    3. B004GRM

      Engage the hook.

    4. for Front Passenger Side:


      1. B004E42

        Engage the claw to install the connector.

    5. w/ Seat Heater System:


      1. B004F7R

        Connect the connector.

      2. Engage the 3 clamps.

  12. INSTALL NO. 2 FRONT SEAT WIRE


    1. Connect each connector and engage each clamp to install the No. 2 front seat wire.

  13. INSTALL RECLINING ADJUSTER EQUALIZING CABLE ASSEMBLY


    1. B004EMF

      Connect the reclining adjuster equalizing cable assembly to install it.

    2. B004EN6N01

      Engage the clamp (A) and install the clamp (B).

  14. INSTALL FRONT SEATBACK HOOK (for Driver Side)


    1. Install the 2 front seatback hooks to the lumbar support adjuster assembly.

  15. INSTALL FRONT SEATBACK HOOK (for Front Passenger Side)


    1. Install the 2 front seatback hooks to the front seatback spring sub-assembly.

  16. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Driver Side)

    Click here

  17. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (for Front Passenger Side)


    1. B004EZ9

      Engage the 2 guides.

    2. Engage the 2 claws to install the front seatback spring sub-assembly to the front seatback frame sub-assembly.

    3. B004GW0

      Install the clamp.

  18. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. B004EVY

      Engage each claw to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.

  19. INSTALL LIMIT SWITCH ASSEMBLY (for LH Side)


    1. B004ERD

      Engage the 2 guides to install the limit switch assembly.

    2. Install the screw.

  20. INSTALL LIMIT SWITCH ASSEMBLY (for RH Side)


    1. B004FDY

      Engage the 2 guides to install the limit switch assembly.

    2. Install the screw.

    3. Connect the connector.

  21. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. B004EFF

      Engage the claw to install the reclining adjuster inside cover LH.

  22. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Perform the same procedure as for the LH side.

  23. INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH


    1. B004F2U

      Engage the guide to install the LH seat reclining adjuster inside cover LH.

    2. Install the screw.

  24. INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH


    1. B004FPQ

      Engage the guide to install the LH seat reclining adjuster inside cover RH.

    2. Install the screw.

  25. INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. B004EK6

      Install the seatback climate control blower.

    2. B004E2A

      Install the clip.

    3. Connect the connector.

  26. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    Click here

  27. INSTALL FRONT SEATBACK PAD WITH COVER


    1. Temporarily install the front seatback pad with cover.

      Note

      Be careful not to damage the front seatback pad with cover.

    2. B004E86C01
      *a Bracket

      Engage the 2 brackets and install the front seatback pad with cover with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a front seat airbag assembly, the front seatback pad with cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the brackets securely.

    3. w/ Climate Control Seat System:


      1. B004G7Z

        Engage the 2 claws to install the seatback climate control blower to the front seatback pad with cover.

  28. INSTALL FRONT SEAT HEADREST SUPPORT


    1. B004FOI

      Engage each claw to install the 2 front seat headrest supports.

    2. B004GR2

      Close the 2 fasteners.

    3. B004F2YC01
      B004FOV Tab

      Insert the 2 tabs.

    4. B004EKOC01
      B004FOV Fastener

      Engage the 2 fasteners.

    5. B004G2J

      Using hog ring pliers, install 3 new hog rings.

      Note


      • Be careful not to damage the front seatback pad with cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seatback pad with cover.

  29. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY


    1. B004EO0

      Connect the reclining adjuster equalizing cable assembly to the reclining remote control lever sub-assembly.

    2. B004E5E

      Engage the 2 guides to install the reclining remote control lever sub-assembly.

    3. B004F1J

      Install the 2 screws.

  30. INSTALL RECLINING REMOTE CONTROL CAP


    1. B004FF1

      Engage the claw and 2 guides to install the reclining remote control cap.

  31. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    1. B004E7Z

      Using a T40 "TORX" socket wrench, install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. B004E2M

      Install the clip.

    3. w/ Seat Heater System:


      1. B004EIW

        Engage the clamp.

      2. Connect the connector.

    4. B004E4R

      Engage the claw and 3 clamps.

      Tech Tips

      Engage the claw first.

    5. B004GDZC01
      B004FOV Fastener

      Engage the fastener to secure the front seat airbag assembly wire harness.

    6. B004GTS

      Engage the clamp.

    7. Connect the connector.

    8. B004EKP

      Connect the connector.

  32. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side)

    Click here

  33. INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY

    Click here

  34. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B004FPL

      Engage the 4 claws to install the reclining power seat switch knob.

  35. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B004E5J

      Engage the 4 claws to install the slide and vertical power seat switch knob.

  36. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  37. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  38. INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. B004GK1

      Engage the 2 claws and 3 guides to install the front seat inner cushion shield.

    2. B004EET

      Install the screw.

  39. INSTALL FRONT SEAT CUSHION SHIELD


    1. for Driver Side:


      1. B004FTZ

        Connect the connector to the front lumbar power seat switch.

    2. B004FTQ

      Connect the 2 connectors to the position control ECU and switch assembly.

    3. B004E8F

      Engage the 3 claws to close the wire harness cover.

    4. B004GWS

      Engage the 2 clamps.

    5. B004EZX

      Engage the 2 guides and clip to install the front seat cushion shield.

    6. B004G9K

      Engage the claw and 3 guides.

  40. INSTALL INNER NO. 1 FRONT SEAT CUSHION SHIELD


    1. B004GF9

      Engage the clamp.

    2. B004GDB

      Install the clip to the inner No. 1 front seat cushion shield.

    3. B004EDO

      Engage the 3 guides to install the inner No. 1 front seat cushion shield.

    4. B004FTPC01
      B004EIV Slide

      Engage the 2 claws as shown in the illustration.

    5. B004F5O

      Engage the claw.

    6. B004EXL

      Engage the clip.

    7. B004EG0

      Install the screw.

  41. CONNECT FRONT SEATBACK PAD WITH COVER


    1. B004E70

      Engage the 2 hooks to connect each rubber band of the front seatback pad with cover.

  42. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

    Click here

  43. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here