POWER MIRROR CONTROL SYSTEM(w/o Memory) Reverse Shift-linked Function of Power Mirrors does not Operate

DESCRIPTION

The ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Based on the signal, each outer mirror control ECU assembly then performs control.

WIRING DIAGRAM

B005L88E16

CAUTION / NOTICE / HINT

Note


  • The power mirror control system (w/o Memory) uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

Tech Tips

The reverse shift-linked function will not activate when both the mirror select switch L and R switch are off.

PROCEDURE


  1. CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION


    1. Check electrical remote control mirror function.

      Click here

      Result
      Result Proceed to
      Mirror function is normal A
      Mirror function is not normal B

    B

    GO TO PROBLEM SYMPTOMS TABLE Click here

    A

  2. CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / DTC.

    5. Check if SFI system DTCs are output.


      Powertrain > Engine > Trouble Codes
      OK
      SFI system DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO SFI SYSTEM for 8AR-FTS: Click here
    GO TO SFI SYSTEM for 2GR-FKS with Canister Pump Module: Click here
    GO TO SFI SYSTEM for 2GR-FKS without Canister Pump Module: Click here

    OK

  3. CHECK COMBINATION METER ASSEMBLY


    1. Check if the shift position indicator light in the combination meter assembly operates normally.

      OK
      Shift position indicator light indicates the actual shift position correctly.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO METER / GAUGE SYSTEM Click here

    OK

  4. CHECK REVERSE SHIFT-LINKED FUNCTION


    1. B005PUGC03
      *a Turns Downward

      Turn the engine switch on (IG).

    2. Turn the mirror select switch R or L switch on.

    3. Check that the mirror surface turns downward when the shift lever is moved to R.

      Result
      Result Proceed to
      Reverse shift-linked functions on both mirrors are not normal A
      Reverse shift-linked function on driver door is not normal B
      Reverse shift-linked function on front passenger door is not normal C

    B

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) Click here

    C

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) Click here

    A

  5. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Master Switch / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Master Switch > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON

      OFF: Mirror select switch off

      ON: Mirror select switch L switch on

      		 -
      Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON

      OFF: Mirror select switch off

      ON: Mirror select switch R switch on

      		 -

      Body Electrical > Master Switch > Data List
      Tester Display
      Mirror Selection SW (L)
      Mirror Selection SW (R)
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

  6. REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)


    1. Temporarily replace the outer rear view mirror assembly (driver door) with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. CHECK REVERSE SHIFT-LINKED FUNCTION


    1. Check reverse shift-linked function.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) Click here

  8. REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)


    1. Temporarily replace the outer rear view mirror assembly (front passenger door) with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  9. CHECK REVERSE SHIFT-LINKED FUNCTION


    1. Check reverse shift-linked function.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) Click here