POWER SEAT SWITCH(for Rear No. 2 Seat) INSPECTION

PROCEDURE


  1. INSPECT FOLD SEAT SWITCH ASSEMBLY


    1. Inspect fold seat switch assembly


      1. B005MYXC02
        *a Return switch
        *b Fold switch
        *c

        Component without harness connected

        (Fold Seat Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Ground
        Tester Connection Condition Specified Condition
        8 - 7 Fold switch (RH) pushed Below 50 Ω
        3 - 7 Return switch (RH) pushed Below 50 Ω
        6 - 7 Fold switch (LH) pushed Below 50 Ω
        1 - 7 Return switch (LH) pushed Below 50 Ω
        Fold Switch (RH)
        Tester Connection Condition Specified Condition
        8 - 7 Fold switch (RH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher
        Return Switch (RH)
        Tester Connection Condition Specified Condition
        3 - 7 Return switch (RH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher
        Fold Switch (LH)
        Tester Connection Condition Specified Condition
        6 - 7 Fold switch (LH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher
        Return Switch (LH)
        Tester Connection Condition Specified Condition
        1 - 7 Return switch (LH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher

    2. Check that the illuminates.


      1. Apply battery voltage to the fold seat switch assembly and check that the illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) → 5

        Battery negative (-) → 4

        		 Illuminates

  2. INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY


    1. Inspect No. 1 fold seat switch assembly


      1. B005M36C02
        *a Return switch
        *b Fold switch
        *c

        Component without harness connected

        (No. 1 Fold Seat Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Ground
        Tester Connection Condition Specified Condition
        6 - 7 Fold switch (RH) pushed Below 50 Ω
        1 - 7 Return switch (RH) pushed Below 50 Ω
        8 - 7 Fold switch (LH) pushed Below 50 Ω
        3 - 7 Return switch (LH) pushed Below 50 Ω
        Fold Switch (RH)
        Tester Connection Condition Specified Condition
        6 - 7 Fold switch (RH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher
        Return Switch (RH)
        Tester Connection Condition Specified Condition
        1 - 7 Return switch (RH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher
        Fold Switch (LH)
        Tester Connection Condition Specified Condition
        8 - 7 Fold switch (LH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher
        Return Switch (LH)
        Tester Connection Condition Specified Condition
        3 - 7 Return switch (LH) pushed Below 50 Ω
        Not pushed 10 kΩ or higher

    2. Check that the illuminates.


      1. Apply battery voltage to the No. 1 fold seat switch assembly and check that the illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) → 5

        Battery negative (-) → 4

        		 Illuminates