REAR SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. INSTALL REAR SEAT ASSEMBLY RH


    1. Place the rear seat assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Lift the seat track adjusting handle and move the rear seat assembly RH to the rearmost position.

    3. Temporarily install the 2 bolts to the front side of the rear seat assembly RH.

    4. Lift the seat track adjusting handle and move the rear seat assembly RH to the foremost position.

    5. Temporarily install the 3 bolts to the rear side of the rear seat assembly RH.

    6. Connect the rear seat airbag assembly connector under the rear seat assembly RH.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B005LY6C01
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    7. Connect the connector.

    8. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

      Click here

    9. B005LWJC02
      *a Rubber Band

      Pass the rear seat center inner belt assembly through the rubber band of the rear seat cushion assembly RH as shown in the illustration.

    10. B005OFIN01

      Tighten the 2 bolts on the front side of the rear seat assembly RH.

      Torque:
      36.7 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

    11. B005MGDN01

      Tighten the 3 bolts on the rear side of the rear seat assembly RH to install it.

      Torque:
      36.7 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

  2. CONNECT REAR SEAT RECLINING CONTROL CABLE (for Manual Seat)


    1. When replacing the rear seat reclining control cable with a new one:


      1. B005MBVN01

        Cut the joint piece at the location (A) shown in the illustration and remove it from the reclining remote control lever sub-assembly RH.

      2. B005O9X

        Install a new joint piece to the reclining remote control lever sub-assembly RH as shown in the illustration.

    2. When replacing the reclining remote control lever sub-assembly RH with a new one:


      1. B005N5Q

        Install a new reclining remote control lever sub-assembly RH to the joint piece as shown in the illustration.

    3. Connect the reclining remote control lever sub-assembly RH to the joint case as shown in the illustration.

      B005NKS

    4. Move the joint piece to the location shown in the illustration and pull up the lock pin to secure it.

      B005L9KC01
      *a Lock Pin - -
    5. B005LR3C01
      B005OOA Install in this Direction

      Connect the rear seat reclining control cable as shown in the illustration.

    6. B005L4ZC01
      B005OOA Install in this Direction

      Install the joint case cover to the joint case as shown in the illustration.

    7. B005LEW

      Connect the rear seat reclining control cable to the joint case as shown in the illustration.

    8. Push in the lock lever of the adjuster spring to lock it as shown in the illustration.

      B005N7JC02
      *a Adjuster Spring *b Lock Lever

  3. CONNECT REAR SEAT ASSEMBLY RH


    1. Engage the fastener to connect the rear seat assembly RH.

    2. Install the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

    3. Install the 4 clips.

  4. INSTALL REAR SEAT OUTER TRACK BRACKET COVER RH


    1. B005P9KC02
      B005OOA Install in this Direction

      Engage the 2 guides and 2 claws to install the rear seat outer track bracket cover RH as shown in the illustration.

  5. INSTALL REAR SEAT INNER TRACK BRACKET COVER RH

    Tech Tips

    Use the same procedure as for the rear seat outer track bracket cover RH.

  6. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY


    1. Install the rear seat center headrest assembly.

  7. INSTALL REAR SEAT HEADREST ASSEMBLY


    1. Install the rear seat headrest assembly.

  8. INSTALL DECK BOARD ASSEMBLY

    Click here

  9. INSTALL TONNEAU COVER ASSEMBLY

    Click here

  10. INSPECT SRS WARNING LIGHT

    Click here