REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH


    1. B005OGCC01
      B005OOA Install in this Direction

      Temporarily install the rear seatback frame sub-assembly LH to the No. 1 seat cushion frame sub-assembly LH as shown in the illustration.

    2. Using a T40 "TORX" socket wrench, temporarily install the 6 bolts.

    3. B005NTM

      Using a T40 "TORX" socket wrench, tighten the 6 bolts while pulling the rear seatback frame sub-assembly LH as shown in the illustration.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  2. INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY LH


    1. B005NII

      Install the reclining control link sub-assembly LH with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY LH


    1. B005L9V

      Install the reclining control link sub-assembly LH with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  4. INSTALL REAR SEAT RECLINING CONTROL CABLE


    1. Route the rear seat reclining control cable as shown in the illustration and engage the clip and clamp.

      B005M5T

    2. Engage the 8 clamps to install the rear seat reclining control cable.

      B005LRO

  5. INSTALL REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY LH


    1. Route the rear No. 1 seat track control cable assembly LH as shown in the illustration and engage the clamp.

      B005NT7

    2. Engage the 6 clamps to install the rear No. 1 seat track control cable assembly LH.

      B005P4E

  6. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY


    1. Route the reclining adjusting cable assembly as shown in the illustration and engage the 2 clamps.

      B005O3W

    2. Engage the 6 clamps to install the reclining adjusting cable assembly.

      B005Q2S

  7. INSTALL REAR SEAT WIRE LH


    1. w/o Seat Belt Warning System:


      1. B005OYC

        Engage the 4 clamps and 2 claws to install the rear seat wire LH.

    2. w/ Seat Belt Warning System:


      1. B005MSH

        Engage the 5 clamps and 2 claws to install the rear seat wire LH.

  8. INSTALL LH SEAT REAR SEAT RECLINING COVER


    1. B005P79C01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the guide as shown in the illustration to install the LH seat rear seat reclining cover.

  9. INSTALL LH SEAT REAR SEAT RECLINING COVER


    1. B005QBVC01
      B005OOA Install in this Direction

      Engage the guide and 5 claws to install the LH seat rear seat reclining cover as shown in the illustration.

  10. INSTALL REAR SEAT INNER RECLINING COVER LH


    1. B005OACC01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the 2 guides, claw and clip as indicated by the arrows, in the order shown in the illustration to install the rear seat inner reclining cover LH.

  11. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005NLAC01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the guide and 2 claws as indicated by the arrows, in the order shown in the illustration to install the rear No. 1 seat reclining adjuster inside cover.

  12. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005NB9C01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the 2 guides and 6 claws as indicated by the arrows, in the order shown in the illustration to install the rear No. 1 seat reclining adjuster inside cover.

  13. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005OE4C01
      B005OOA Install in this Direction

      Engage the guide, 2 claws and clip to install the rear No. 1 seat reclining adjuster inside cover as shown in the illustration.

  14. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005LNPC02
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the guide and 2 claws as indicated by the arrows, in the order shown in the illustration to install the rear No. 1 seat reclining adjuster inside cover.

  15. INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    1. B005OH4C01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the 6 guides and 11 claws as indicated by the arrows, in the order shown in the illustration to install the rear No. 1 seat reclining cover LH.

  16. INSTALL NO. 2 RECLINING LINK COVER LH


    1. B005OVXC02
      B005OOA Install in this Direction

      Engage the guide to install the No. 2 reclining link cover LH as shown in the illustration.

  17. INSTALL NO. 1 RECLINING LINK COVER LH


    1. B005PX1C01
      B005OOA Install in this Direction

      Engage the guide and 5 claws to install the No. 1 reclining link cover LH as shown in the illustration.

  18. INSTALL REAR SEATBACK EDGE PROTECTOR


    1. B005P7H

      Install a new rear seatback edge protector.

  19. INSTALL REAR SEAT AIRBAG ASSEMBLY LH

    Click here

  20. INSTALL SEAT COVER WIRE


    1. B005Q82N02

      Install the 5 seat cover wires.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wires are available as supplied parts.

      • For wires 1000 mm (3.28 ft.) or less in length, cut or shape a 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read Precaution before preparing the wire.

        Click here

      Length
      A 110 mm (4.33 in.)
      B 330 mm (1.0824 ft.)
      C 200 mm (7.87 in.)

      Tech Tips

      The dimension shown in the illustration is the length.

      B005NZL

  21. INSTALL RECLINING REMOTE CONTROL BEZEL LH


    1. B005OKG

      Install the reclining remote control bezel LH.

  22. INSTALL SEPARATE TYPE REAR SEATBACK COVER

    Tech Tips

    When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B005MARN01

      Using hog ring pliers, install 11 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    2. B005LHMN03

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 2 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    3. B005NYGC01
      B005M97 Fastener

      Engage the 2 fasteners.

  23. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.

    2. B005NUD

      Install the 2 rear seatback cover brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a rear seat airbag assembly, the separate type rear seatback cover with pad must be securely installed. Otherwise, the rear seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Make sure that the brackets are installed securely.

    3. B005LGTC01
      B005OOA Install in this Direction

      Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies as shown in the illustration.

    4. B005PNT

      Engage the 12 hooks to install the separate type rear seatback cover with pad.

  24. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH


    1. B005OGM

      Connect the reclining adjusting cable assembly.

    2. B005LMLC01
      B005OOA Install in this Direction

      Engage the guide as shown in the illustration.

    3. B005N2X

      Install the reclining remote control lever sub-assembly LH with the 2 screws.

  25. INSTALL REAR SEAT UPPER RECLINING COVER LH


    1. B005L95C01
      B005OOA Install in this Direction

      Engage the 2 guides and claw to install the rear seat upper reclining cover LH as shown in the illustration.

  26. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    1. B005N27

      Engage the 2 guides to connect the rubber band and install the No. 2 seat cushion cover sub-assembly LH.

  27. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH


    1. B005OFF

      Engage the 3 guides as shown in the illustration.

    2. B005QANC01
      B005OOA Install in this Direction

      Engage the 4 guides and 6 clips to install the rear seatback board carpet assembly LH as shown in the illustration.

  28. INSTALL REAR SEATBACK COVER LH


    1. B005PZKC01
      B005OOA Install in this Direction

      Engage the 6 claws to install the rear seatback cover LH as shown in the illustration.

    2. B005Q51

      Engage the 2 claws as shown in the illustration.

  29. INSTALL REAR SEAT INNER BELT ASSEMBLY LH

    Click here

  30. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005QE1C01
      B005OOA Install in this Direction

      Engage the 3 claws and clip to install the rear No. 1 seat reclining adjuster inside cover as shown in the illustration.

  31. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    1. B005M2D

      Engage the 2 clamps to install the seat heater control sub-assembly LH.

    2. Connect the connector.

  32. INSTALL REAR SEAT CUSHION EDGE PROTECTOR


    1. B005MXS

      Install a new rear seat cushion edge protector.

  33. INSTALL SEAT COVER WIRE


    1. B005QFUN02

      Install the 6 seat cover wires.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wires are available as supplied parts.

      • For wires 1000 mm (3.28 ft.) or less in length, cut or shape a 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read Precaution before preparing the wire.

        Click here

      Length
      A 420 mm (1.3776 ft.)
      B 240 mm (9.45 in.)
      C 90 mm (3.54 in.)

      Tech Tips

      The dimension shown in the illustration is the length.

      B005NZL

  34. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

    Tech Tips

    When installing a separate type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B005PFZN01

      Using hog ring pliers, install 20 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    2. B005MEBN01

      Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 6 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    3. B005QEYC01
      B005M97 Fastener

      Engage the fastener.

  35. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


    1. Temporarily install the separate type rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly LH.

    2. Engage the 9 hooks.

      B005QDU
    3. B005PYX

      Engage the hook.

    4. B005LWW

      Engage the 2 clamps.

    5. w/ Seat Heater System:


      1. B005P1R

        Engage the 3 clamps.

      2. Connect the 2 connectors.

    6. B005MKG

      Engage the 4 hooks to install the separate type rear seat cushion cover with pad.

  36. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    1. B005MU6

      Connect the rear seat reclining control cable.

    2. B005MGJC02
      B005OOA Install in this Direction

      Engage the guide as shown in the illustration.

    3. B005OJJ

      Install the rear seat lock control lever sub-assembly LH with the 2 screws.

    4. B005O8Y

      Engage the hook.

    5. B005L3X

      Engage the clamp to connect the rear seat reclining control cable.

    6. B005LW1

      Engage the 3 hooks.

  37. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH


    1. B005O84

      Install the No. 1 reclining adjuster release handle LH with the 3 screws.

  38. INSTALL REAR SEAT COVER CAP LH


    1. B005OJY

      Engage the 2 guides and 2 claws to install the rear seat cover cap LH.

  39. INSTALL SEAT ADJUSTER COVER CAP


    1. B005M6W

      Install the 2 seat adjuster cover caps.