REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH


    1. Temporarily install the rear seatback frame sub-assembly RH to the No. 1 seat cushion frame sub-assembly RH as shown in the illustration.

      B005MTCC01
      B005NIZ Bolt (A) B005LWS Bolt (B)
      B005OOA Install in this Direction - -

    2. Using a T40 "TORX" socket wrench, temporarily install the 4 bolts (B).

    3. Using a T55 "TORX" socket wrench, temporarily install the 2 bolts (A).

    4. Using a T40 "TORX" socket wrench, tighten the 4 bolts (B) while pulling the rear seatback frame sub-assembly RH as shown in the illustration.

      B005MM3C01
      B005NIZ Bolt (A) B005LWS Bolt (B)
      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

    5. Using a T55 "TORX" socket wrench, tighten the 2 bolts (A) to install the rear seatback frame sub-assembly RH.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  2. INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY RH


    1. B005O40

      Install the reclining control link sub-assembly RH with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY RH


    1. B005PL1

      Install the reclining control link sub-assembly RH with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  4. INSTALL REAR SEAT RECLINING CONTROL CABLE


    1. Route the rear seat reclining control cable as shown in the illustration and engage the clip and clamp.

      B005N5O

    2. Engage the 8 clamps to install the rear seat reclining control cable.

      B005LTH

  5. INSTALL REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY RH


    1. Route the rear No. 1 seat track control cable assembly RH as shown in the illustration and engage the clamp.

      B005NFX

    2. Engage the 6 clamps to install the rear No. 1 seat track control cable assembly RH.

      B005PXG

  6. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY


    1. Route the reclining adjusting cable assembly as shown in the illustration and engage the 2 clamps.

      B005NQV

    2. Engage the 6 clamps to install the reclining adjusting cable assembly.

      B005MJ3

  7. INSTALL REAR SEAT WIRE RH


    1. w/o Seat Belt Warning System:


      1. B005OCT

        Engage the 7 clamps and 2 claws to install the rear seat wire RH.

    2. w/ Seat Belt Warning System:


      1. B005N8G

        Engage the 9 clamps and 2 claws to install the rear seat wire RH.

  8. INSTALL RH SEAT REAR SEAT RECLINING COVER


    1. B005PKQC01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the guide as shown in the illustration to install the RH seat rear seat reclining cover.

  9. INSTALL RH SEAT REAR SEAT RECLINING COVER


    1. B005LJCC01
      B005OOA Install in this Direction

      Engage the guide and 5 claws to install the RH seat rear seat reclining cover as shown in the illustration.

  10. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005OYLC01
      B005OOA Install in this Direction

      Engage the guide to install the rear No. 1 seat reclining adjuster inside cover as shown in the illustration.

  11. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005N9TC01
      B005OOA Install in this Direction

      Engage the 2 guides and 3 claws to install the rear No. 1 seat reclining adjuster inside cover as shown in the illustration.

  12. INSTALL REAR SEAT INNER RECLINING COVER RH


    1. B005MWYC01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the 9 guides and 9 claws as indicated by the arrows, in the order shown in the illustration to install the rear seat inner reclining cover RH.

  13. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005O0UC01
      B005OOA Install in this Direction

      Engage the guide, clip and 2 claws to install the rear No. 1 seat reclining adjuster inside cover as shown in the illustration.

  14. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005O5CC01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the 2 guides and 3 claws as indicated by the arrows, in the order shown in the illustration to install the rear No. 1 seat reclining adjuster inside cover.

  15. INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    1. B005OLDC01
      B005OOA Install in this Direction (1)
      B005OMH Install in this Direction (2)

      Engage the 7 guides and 10 claws as indicated by the arrows, in the order shown in the illustration to install the rear No. 1 seat reclining cover RH.

  16. INSTALL NO. 2 RECLINING LINK COVER RH


    1. B005N3IC01
      B005OOA Install in this Direction

      Engage the guide to install the No. 2 reclining link cover RH as shown in the illustration.

  17. INSTALL NO. 1 RECLINING LINK COVER RH


    1. B005Q0CC01
      B005OOA Install in this Direction

      Engage the guide and 5 claws to install the No. 1 reclining link cover RH as shown in the illustration.

  18. INSTALL CENTER SEAT HINGE COVER RH


    1. B005LQKC01
      B005OOA Install in this Direction

      Engage the 5 claws to install the center seat hinge cover RH as shown in the illustration.

  19. INSTALL REAR SEAT CUSHION SPRING DAMPER RH


    1. B005LL9

      Engage the guide.

    2. Install the rear seat cushion spring damper RH with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  20. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

    Click here

  21. INSTALL REAR SEATBACK EDGE PROTECTOR


    1. B005PD9

      Install a new rear seatback edge protector.

  22. INSTALL REAR SEAT AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  23. INSTALL SEAT COVER WIRE


    1. B005PQCN01

      Install the 5 seat cover wires.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wires are available as supplied parts.

      • For wires 1000 mm (3.28 ft.) or less in length, cut or shape a 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read Precaution before preparing the wire.

        Click here

      Length
      A 110 mm (4.33 in.)
      B 330 mm (1.0824 ft.)
      C 200 mm (7.87 in.)

      Tech Tips

      The dimension shown in the illustration is the length.

      B005NZL

  24. INSTALL RECLINING REMOTE CONTROL BEZEL RH


    1. B005NP1

      Install the reclining remote control bezel RH.

  25. INSTALL SEPARATE TYPE REAR SEATBACK COVER

    Tech Tips

    When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B005N8CN01

      Using hog ring pliers, install 11 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    2. B005PLKN01

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 2 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog ring as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  26. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.

    2. B005OBL

      Install the 2 rear seatback cover brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a rear seat airbag assembly, the separate type rear seatback cover with pad must be securely installed. Otherwise, the rear seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Make sure that the brackets are installed securely.

    3. B005MRMC01
      B005OOA Install in this Direction

      Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies as shown in the illustration.

    4. B005P7YC01
      B005M97 Fastener

      Engage the hook and fastener.

    5. B005MU3

      Engage the 12 hooks to install the separate type rear seatback cover with pad.

  27. INSTALL REAR SEAT SHOULDER BELT COVER


    1. B005NO6

      Pass rear center seat outer belt assembly through the rear seat shoulder belt cover and engage the 2 guides and 2 claws to install it.

  28. INSTALL SEAT BELT ANCHOR COVER CAP


    1. B005LLFC01
      B005OOA Install in this Direction

      Engage the 2 guides to install the seat belt anchor cap as shown in the illustration.

  29. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH


    1. B005LX2

      Connect the reclining adjusting cable assembly.

    2. B005LCPC01
      B005OOA Install in this Direction

      Engage the guide as shown in the illustration.

    3. B005MTQ

      Install the reclining remote control lever sub-assembly RH with the 2 screws.

  30. INSTALL REAR SEAT UPPER RECLINING COVER RH


    1. B005MUEC01
      B005OOA Install in this Direction

      Engage the 2 guides and claw to install the rear seat upper reclining cover RH as shown in the illustration.

  31. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH


    1. B005QEE

      Engage the 2 guides to connect the rubber band and install the No. 2 seat cushion cover sub-assembly RH.

  32. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH


    1. B005M2W

      Engage the 3 guides as shown in the illustration.

    2. B005M6JC01
      B005OOA Install in this Direction

      Engage the 4 guides and 6 clips to install the rear seatback board carpet assembly RH as shown in the illustration.

  33. INSTALL REAR SEATBACK COVER RH


    1. B005L2GC01
      B005OOA Install in this Direction

      Engage the 6 claws to install the rear seatback cover RH as shown in the illustration.

    2. B005NSC

      Engage the 2 claws as shown in the illustration.

  34. INSTALL REAR SEATBACK LOCK ASSEMBLY RH


    1. B005N69

      Install the rear seatback lock assembly RH with the 2 bolts.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

  35. INSTALL NO. 2 CENTER SEATBACK COVER


    1. B005MQH

      Install the No. 2 center seatback cover with the 3 screws.

  36. INSTALL REAR SEATBACK LOCK LEVER


    1. Engage the claw and guide to install the rear seatback lock lever as shown in the illustration.

      B005MEPC01
      B005OOA Install in this Direction (1) B005OMH Install in this Direction (2)
    2. B005OZGC01
      B005OOA Install in this Direction

      Connect the fold seatback wire as shown in the illustration.

    3. B005M6K

      Engage the retainer as shown in the illustration to install the fold seatback wire.

  37. INSTALL NO. 1 SEATBACK COVER


    1. B005OEL

      Engage the 3 claws and 3 clips to install the No. 1 seatback cover.

    2. B005M7NC01
      B005OOA Install in this Direction

      Engage the 4 claws to install the 2 rear seat headrest support assemblies as shown in the illustration.

  38. INSTALL HEADPHONE TERMINAL LH (w/ Rear Seat Entertainment System)

    Click here

  39. INSTALL HEADPHONE TERMINAL RH (w/ Rear Seat Entertainment System)

    Tech Tips

    Use the same procedure as for the LH side.

  40. INSTALL REAR SEAT HEATER SWITCH (w/ Seat Heater System)


    1. B005OMU

      Install the rear seat heater switch with the 3 screws.

  41. INSTALL REAR CONSOLE BOX WIRE


    1. w/ Rear Seat Entertainment System or Seat Heater System:


      1. B005O5TC01
        *A w/ Rear Seat Entertainment System
        *B w/ Seat Heater System
        *C w/ Rear Seat Entertainment System or Seat Heater System

        Engage each clamp.

    2. Connect each connector to install the rear console box wire.

  42. INSTALL NO. 2 REAR SEAT CENTER ARMREST BOX


    1. B005O4B

      Engage the clamp.

    2. Install the No. 2 rear seat center armrest box with the 5 screws.

  43. INSTALL CENTER ARMREST LOCK SUB-ASSEMBLY


    1. B005NN5

      Install the center armrest lock sub-assembly to the No. 1 rear seat center armrest cover with the 4 screws.

    2. B005NK5

      Engage the 2 claws.

    3. Install the rear seat center armrest plate with the 4 screws.

  44. INSTALL REAR SEAT CENTER ARMREST DOOR SUB-ASSEMBLY


    1. B005QA2

      Install the rear seat center armrest door sub-assembly with the 2 screws.

  45. INSTALL CUP HOLDER ASSEMBLY


    1. B005L8M

      Install the cup holder assembly with the 2 screws.

  46. INSTALL REAR SEAT CENTER ARMREST COVER


    1. B005MGO

      Install the 2 rear seat center armrest covers.

  47. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    1. Engage the guide as shown in the illustration.

      B005M09C01
      B005OOA Install in this Direction (1) B005OMH Install in this Direction (2)
    2. B005N2M

      Using a T45 "TORX" socket wrench, install the rear seat center armrest assembly with the 2 No. 1 rear seat reclining spacers and 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    3. B005QDO

      Engage the 3 clips.

    4. Fold the rear seat center armrest assembly as shown in the illustration.

      B005MNV
    5. B005NVNC01
      *a Hook
      *b Clamp

      Engage the clamp and 2 hooks.

    6. B005Q27

      Engage the 2 clips to install the rear seat center armrest cover sub-assembly.

    7. B005MFLC01
      B005OOA Install in this Direction

      Install the rear No. 1 seat center armrest plate as shown in the illustration.

    8. B005LV2

      Using a T30 "TORX" socket wrench, install the rear seatback hinge with the bolt.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

  48. INSTALL CENTER ARMREST HINGE COVER RH


    1. B005MVRC01
      B005OOA Install in this Direction

      Engage the 6 guides and 7 claws to install the center armrest hinge cover RH as shown in the illustration.

  49. INSTALL ARMREST ASSEMBLY


    1. B005NR1C01
      *a Pin

      Engage the rear seatback hinge to the pin of the center armrest hinge cover RH as shown in the illustration.

      Note

      If the rear seatback hinge is not engaged to the pin of the center armrest hinge cover RH, the armrest assembly cannot be installed as it will interfere with the rear seatback frame sub-assembly RH.

    2. Engage the pin and temporarily install the armrest assembly as shown in the illustration.

      B005Q7CC01
      B005OOA Install in this Direction (1) B005OMH Install in this Direction (2)
    3. B005OIIC01
      *a Pin

      Disengage the rear seatback hinge from the pin of the center armrest hinge cover RH as shown in the illustration.

    4. B005P8MC01
      *a Bolt (A)
      *b Bolt (B)

      Using a T45 "TORX" socket wrench, install the armrest assembly with the 2 No. 2 rear seat reclining spacers, bolt (A) and bolt (B).

      Torque:
      Bolt (A)
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
      Bolt (B)
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }
    5. B005N73

      Install the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    6. Using a T30 "TORX" socket wrench, install the rear seatback center hinge sub-assembly with the bolt.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

  50. INSTALL NO. 1 SEAT ARMREST ASSEMBLY


    1. B005MA7

      Engage the 2 clips.

    2. B005QG2

      Install the No. 1 seat armrest assembly with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    3. B005OHX

      Engage the clamp.

    4. Connect the connector.

  51. INSTALL CENTER ARMREST HINGE COVER LH


    1. B005MKLC01
      B005OOA Install in this Direction

      Engage the 6 guides and 7 claws to install the center armrest hinge cover LH as shown in the illustration.

  52. INSTALL REAR CENTER SEAT CUSHION COVER SUB-ASSEMBLY


    1. B005PX0

      Engage the 2 guides to connect the rubber band and install the rear center seat cushion cover sub-assembly.

  53. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY


    1. B005ONDC03
      B005OOA Install in this Direction

      Engage the 5 clips and 10 claws to install the rear seatback board sub-assembly as shown in the illustration.

  54. INSTALL REAR SEATBACK COVER (w/ Cover)


    1. B005LQ5C01
      B005OOA Install in this Direction

      Engage the 6 claws to install the rear seatback cover as shown in the illustration.

    2. B005PWW

      Engage the 2 claws as shown in the illustration.

  55. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

    Click here

  56. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

    Click here

  57. INSTALL REAR NO. 1 SEAT RECLINING ADJUSTER INSIDE COVER


    1. B005LJMC01
      B005OOA Install in this Direction

      Engage the clip and 3 claws to install the rear No. 1 seat reclining adjuster inside cover as shown in the illustration.

  58. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY

    Click here

  59. INSTALL CENTER SEAT HINGE COVER LH


    1. B005O9FC01
      B005OOA Install in this Direction

      Engage the guide, clip and 5 claws to install the center seat hinge cover LH as shown in the illustration.

  60. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)


    1. B005NMB

      Engage the 2 clamps to install the seat heater control sub-assembly RH.

    2. Connect the connector.

  61. INSTALL REAR SEAT CUSHION EDGE PROTECTOR


    1. B005OI4

      Install a new rear seat cushion edge protector.

  62. INSTALL SEAT COVER WIRE


    1. B005OYKN01

      Install the 6 seat cover wires.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wires are available as supplied parts.

      • For wires 1000 mm (3.28 ft.) or less in length, cut or shape a 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read Precaution before preparing the wire.

        Click here

      Length
      A 420 mm (1.3776 ft.)
      B 240 mm (9.45 in.)
      C 90 mm (3.54 in.)

      Tech Tips

      The dimension shown in the illustration is the length.

      B005NZL

  63. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

    Tech Tips

    When installing a separate type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B005MJ9N01

      Using hog ring pliers, install 20 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    2. B005NVZN01

      Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad RH with 10 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

  64. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


    1. Temporarily install the separate type rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly RH.

    2. B005O5Y

      Engage the 11 hooks.

    3. B005NRM

      Engage the 6 hooks.

    4. B005Q5D

      Engage the hook.

    5. B005M54

      Engage the 2 clamps.

    6. B005PSM

      w/ Seat Heater System:


      1. Engage the 3 clamps.

      2. Connect the 2 connectors.

    7. B005O1A

      Engage the 8 hooks.

    8. B005NUP

      Engage the 4 hooks to install the separate type rear seat cushion cover with pad.

    9. B005OJXC01
      *a Rubber Band
      B005OOA Install in this Direction

      Pass the rear center seat inner belt assembly through the rubber band of the separate type rear seat cushion cover as shown in the illustration.

  65. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    1. B005P4S

      Connect the rear seat reclining control cable.

    2. B005QG3C01
      B005OOA Install in this Direction

      Engage the guide as shown in the illustration.

    3. B005ONQ

      Install the rear seat lock control lever sub-assembly RH with the 2 screws.

    4. B005Q6M

      Engage the clamp to connect the rear seat reclining control cable.

    5. B005PNW

      Engage the 3 hooks.

  66. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH


    1. B005LYP

      Install the No. 1 reclining adjuster release handle RH with the 3 screws.

  67. INSTALL REAR SEAT COVER CAP RH


    1. B005PBP

      Engage the 2 guides and 2 claws to install the rear seat cover cap RH.

  68. INSTALL SEAT ADJUSTER COVER CAP


    1. B005N8A

      Install the 2 seat adjuster cover caps.