SEAT HEATER SYSTEM, Diagnostic DTC:B14C0

DTC Code DTC Name
B14C0 Front Right Seat Heat Sensor Circuit

DESCRIPTION

Power supply to the temperature sensor built into the front seat cushion heater stops if one of the following occurs: 1) an open or short occurs in the temperature sensor circuit; or 2) the temperature sensor is damaged and its output value does not change.

DTC No. Detection Item DTC Detection Condition Trouble Area
B14C0 Front Right Seat Heat Sensor Circuit Seat heater temperature sensor malfunction

  • Air conditioning amplifier assembly

  • Front seat cushion heater (separate type front seat cushion cover (for RH side))*1

  • Front seat cushion heater (front seat cushion pad with cover RH)*2

  • Wire harness or connector

WIRING DIAGRAM

B005OD8E26

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      OK
      DTC B14C0 is not output.
      Result
      Result Proceed to
      OK A
      NG (for Standard Seat Type) B
      NG (for Sports Seat Type) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    INSPECT FRONT SEAT CUSHION HEATER (FRONT SEAT CUSHION PAD WITH COVER RH) Click here

    B

  3. INSPECT FRONT SEAT CUSHION HEATER (SEPARATE TYPE FRONT SEAT CUSHION COVER (FOR RH SIDE))


    1. Remove the front seat cushion heater (separate type front seat cushion cover (for RH side)).

      Click here

    2. Inspect the front seat cushion heater (separate type front seat cushion cover (for RH side)).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT CUSHION HEATER (SEPARATE TYPE FRONT SEAT CUSHION COVER (FOR RH SIDE)) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER (SEPARATE TYPE FRONT SEAT CUSHION COVER (FOR RH SIDE)))


    1. Disconnect the J48 air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J48-18 (TSR) - b6-6 (THR) Always Below 1 Ω
      J48-18 (TSR) or b6-6 (THR) - Body ground Always 10 kΩ or higher
      J48-9 (SG-6) - b6-4 (PR) Always Below 1 Ω
      J48-9 (SG-6) or b6-4 (PR) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT FRONT SEAT CUSHION HEATER (FRONT SEAT CUSHION PAD WITH COVER RH)


    1. Remove the front seat cushion heater (front seat cushion pad with cover RH).

      Click here

    2. Inspect the front seat cushion heater (front seat cushion pad with cover RH).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT CUSHION HEATER (FRONT SEAT CUSHION PAD WITH COVER RH) Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER (FRONT SEAT CUSHION PAD WITH COVER RH))


    1. Disconnect the J48 air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J48-18 (TSR) - b6-6 (THR) Always Below 1 Ω
      J48-18 (TSR) or b6-6 (THR) - Body ground Always 10 kΩ or higher
      J48-9 (SG-6) - b6-4 (PR) Always Below 1 Ω
      J48-9 (SG-6) or b6-4 (PR) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR