IMMOBILISER SYSTEM Security Indicator Light Does not Blink

DESCRIPTION


WIRING DIAGRAM

B005NJ8E04

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE


  1. CHECK FOR DTC


    1. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Powertrain > Engine > Trouble Codes
      OK
      DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    OK

  2. PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Type Diagnostic Note
      Immobiliser Indicator Security indicator light OFF/ON -

      Body Electrical > Entry&Start > Active Test
      Tester Display
      Immobiliser Indicator
      OK
      The security indicator light (radio receiver assembly) operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY)) Click here

    OK

  3. CHECK SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY) OPERATION


    1. When the immobiliser is set, check that the security indicator light (radio receiver assembly) blinks.*1

      OK
      The security indicator light (radio receiver assembly) blinks normally.

    2. When the theft deterrent system is in the arming preparation state, check that the security indicator light (radio receiver assembly) illuminates.*2

      OK
      The security indicator light (radio receiver assembly) illuminates normally.
      Result
      Result Proceed to
      *1 is NG (*2 is OK) A
      *2 is NG (*1 is OK) B

    A

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY))


    1. Disconnect the J41 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the J50*1 or J49*2 security indicator light (radio receiver assembly) connector.


      • *1: for Navigation System

      • *2: for Audio Visual System

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Navigation System
      Tester Connection Condition Specified Condition
      J41-20 (IND) - J50-37 (SEUC) Always Below 1 Ω
      J41-20 (IND) or J50-37 (SEUC) - Body ground Always 10 kΩ or higher
      for Audio Visual System
      Tester Connection Condition Specified Condition
      J41-20 (IND) - J49-16 (SEUC) Always Below 1 Ω
      J41-20 (IND) or J49-16 (SEUC) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Reconnect the O6 certification ECU (smart key ECU assembly) connector.

    2. Reconnect the J50*1 or J49*2 security indicator light (radio receiver assembly) connector.


      • *1: for Navigation System

      • *2: for Audio Visual System

    3. Using an oscilloscope, check the waveform.

      B005P5KC11
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 - -
      Measurement Condition
      Tester Connection Condition Specified Condition
      J41-20 (IND) - Body ground Engine switch off → on (IG) Pulse generation → Below 2 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY) Click here

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)