QUARTER WINDOW GLASS(w/ Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  2. REMOVE REAR DOOR SCUFF PLATE

    Click here

  3. REMOVE REAR DOOR INSIDE SCUFF PLATE

    Click here

  4. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH (for LH Side)

    Click here

  5. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH (for RH Side)

    Click here

  6. REMOVE FRONT DECK SIDE TRIM COVER

    Click here

  7. REMOVE REAR SEAT SIDE GARNISH

    Click here

  8. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

    Click here

  9. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

    Click here

  10. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

    Click here

  11. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

    Click here

  12. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)

    Click here

  14. REMOVE NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (for LH Side)

    Click here

  15. REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (for LH Side)

    Click here

  16. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

    Click here

  17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

    Click here

  18. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY

    Click here

  19. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

    Click here

  20. REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY

    Click here

  21. REMOVE QUARTER WINDOW ASSEMBLY


    1. B005O2DC03
      B005M97 Protective Tape

      Apply protective tape to the area around the installation position of the quarter window assembly on the vehicle body to prevent it from being scratched.

    2. B005PE1C02
      *a Piano Wire
      *b Clip

      Pass a piano wire between the vehicle body and quarter window assembly from the interior.

    3. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    4. Cut the adhesive by pulling the piano wire around the quarter window assembly.

      Note

      When separating the quarter window assembly, be careful not to damage the paint or interior and exterior ornaments.

    5. B005L4B

      Using suction cups, disengage the 4 clips and remove the quarter window assembly.

      Note

      Be careful not to drop the quarter window assembly.

  22. CLEAN VEHICLE BODY


    1. Clean and shape the contact surfaces of the vehicle body.


      1. B005LXJC01
        *a Vehicle Body
        B005M97 Adhesive

        Using a knife, cut off any excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

        Standard Dimension
        Area Dimension
        a 1.0 mm (0.0394 in.) or more

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.

    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with non-residue solvent.

      Tech Tips

      Even if all of the adhesive has been removed, clean the vehicle body.