HEATED WINDSHIELD DEFROSTER SYSTEM Heated Windshield Defroster System does not operate

DESCRIPTION

When the front window deicer switch (lower D module switch) assembly is operated, the operation signal is transmitted to the air conditioning amplifier assembly directly. When the air conditioning amplifier assembly receives the signal, it turns on the HWD NO. 1 relay, HWD NO. 2 relay and HWD NO. 3 relay to operate the heated windshield defroster system.

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the battery voltage is low, the heated windshield defroster system may not operate. When "Operation of Electrical Items Restricted." is not displayed on the multi-information display in the combination meter assembly, check the Data List item "Battery Control Count (Body ECU)".

    Click here

  • The heated windshield defroster system uses the CAN communication system. First, confirm that there are no malfunctions in the communication system by checking the communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure

    Click here

  • If the ambient temperature is 5°C (41°F) or higher, or if a malfunction of the ambient temperature sensor (thermistor assembly) is detected, the HWD NO. 3 relay will be deactivated and the front window deicer switch indicator light will blink.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    2. Recheck for DTCs.


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1412/12 is output A
      DTC B1412/12 is not output B

    A

    GO TO AIR CONDITIONING SYSTEM (B1412/12) Click here

    B

  2. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Air Conditioner > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Deicer Relay (Front) Windshield glass (windshield deicer wire) OFF or ON -

      Body Electrical > Air Conditioner > Active Test
      Tester Display
      Deicer Relay (Front)
      OK
      The heated windshield defroster system operates normally.
      Result
      Result Proceed to
      OK A
      NG (Both No. 1 and No. 2 heated windshield defroster does not warm up.) B
      NG (Only No. 1 heated windshield defroster does not warm up.) C
      NG (Only No. 2 heated windshield defroster does not warm up.) D

    B

    INSPECT HWD NO. 3 RELAY Click here

    C

    INSPECT HWD NO. 1 RELAY Click here

    D

    INSPECT HWD NO. 2 RELAY Click here

    A

  3. INSPECT FRONT WINDOW DEICER SWITCH (LOWER D MODULE SWITCH)


    1. Remove the front window deicer switch (lower D module switch).

      Click here

    2. Inspect the front window deicer switch (lower D module switch).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT WINDOW DEICER SWITCH (LOWER D MODULE SWITCH) Click here

    OK

  4. CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH (LOWER D MODULE SWITCH) - IG POWER SUPPLY)


    1. Disconnect the J84 front window deicer switch (lower D module switch) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J84-7 (IG) - Body ground Engine switch off Below 1 V
      Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH (LOWER D MODULE SWITCH) - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Disconnect the J43 and J42 air conditioning amplifier assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J84-20 (D) - J43-22 (IND) Always Below 1 Ω
      J84-20 (D) or J43-22 (IND) - Body ground Always 10 kΩ or higher
      J84-19 (E) - J42-29 (DFAC) Always Below 1 Ω
      J84-19 (E) or J42-29 (DFAC) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. INSPECT HWD NO. 3 RELAY


    1. Inspect the HWD NO. 3 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HWD NO. 3 RELAY

    OK

  7. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 3 RELAY - IG POWER SUPPLY)


    1. B005LKOC01
      *a HWD No. 3 Relay Holder

      for 2GR-FKS


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-1 - Body ground Engine switch on (IG) 11 to 14 V
        HWD NO. 3 relay holder terminal-3 - Body ground Engine switch on (IG) 11 to 14 V
    2. B005PEGC01
      *a HWD No. 3 Relay Holder

      for 8AR-FTS


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-1 - Body ground Engine switch on (IG) 11 to 14 V
        HWD NO. 3 relay holder terminal-3 - Body ground Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 3 RELAY - HWD NO. 1 RELAY OR HWD NO. 2 RELAY)


    1. B005LKOC02
      *a HWD No. 1 Relay Holder
      *b HWD No. 2 Relay Holder
      *c HWD No. 3 Relay Holder

      for 2GR-FKS


      1. Disconnect J43 air conditioning amplifier assembly connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-2 - J43-17 (FDEF) Always Below 1 Ω
        HWD NO. 3 relay holder terminal-2 or J43-17 (FDEF) - Body ground Always 10 kΩ higher
        HWD NO. 3 relay holder terminal-5 - HWD NO. 1 relay holder terminal-2 or HWD NO. 2 relay holder terminal-2 Always Below 1 Ω
        HWD NO. 3 relay holder terminal-5 - Body ground Always 10 kΩ higher
        HWD NO. 1 relay holder terminal-2 - Body ground Always 10 kΩ higher
        HWD NO. 2 relay holder terminal-2 - Body ground Always 10 kΩ higher
    2. B005PEGC02
      *a HWD No. 1 Relay Holder
      *b HWD No. 2 Relay Holder
      *c HWD No. 3 Relay Holder

      for 8AR-FTS


      1. Disconnect J43 air conditioning amplifier assembly connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-2 - J43-17 (FDEF) Always Below 1 Ω
        HWD NO. 3 relay holder terminal-2 or J43-17 (FDEF) - Body ground Always 10 kΩ higher
        HWD NO. 3 relay holder terminal-5 - HWD NO. 1 relay holder terminal-2 or HWD NO. 2 relay holder terminal-2 Always Below 1 Ω
        HWD NO. 3 relay holder terminal-5 - Body ground Always 10 kΩ higher
        HWD NO. 1 relay holder terminal-2 - Body ground Always 10 kΩ higher
        HWD NO. 2 relay holder terminal-2 - Body ground Always 10 kΩ higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. INSPECT HWD NO. 1 RELAY


    1. Inspect the HWD NO. 1 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HWD NO. 1 RELAY

    OK

  10. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - BATTERY)


    1. B005LKOC03
      *a HWD No. 1 Relay Holder

      for 2GR-FKS


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        HWD NO. 1 relay holder terminal-3 - Body ground Always 11 to 14 V
    2. B005PEGC03
      *a HWD No. 1 Relay Holder

      for 8AR-FTS


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        HWD NO. 1 relay holder terminal-3 - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - HWD NO. 3 RELAY)


    1. B005LKOC04
      *a HWD No. 1 Relay Holder
      *b HWD No. 3 Relay Holder

      for 2GR-FKS

      Standard Resistance
      Tester Connection Condition Specified Condition
      HWD NO. 3 relay holder terminal-5 - HWD NO. 1 relay holder terminal-2 Always Below 1 Ω
      HWD NO. 3 relay holder terminal-5 or HWD NO. 1 relay holder terminal-2 - Body ground Always 10 kΩ higher

      1. Measure the resistance according to the value(s) in the table below.

    2. B005PEGC04
      *a HWD No. 1 Relay Holder
      *b HWD No. 3 Relay Holder

      for 8AR-FTS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-5 - HWD NO. 1 relay holder terminal-2 Always Below 1 Ω
        HWD NO. 3 relay holder terminal-5 or HWD NO. 1 relay holder terminal-2 - Body ground Always 10 kΩ higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - BODY GROUND)


    1. B005LKOC03
      *a HWD No. 1 Relay Holder

      for 2GR-FKS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 1 relay holder terminal-1 - Body ground Always Below 1 Ω
    2. B005PEGE02

      for 8AR-FTS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 1 relay holder terminal-1 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - NO. 1 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS))


    1. B005LKOC03
      *a HWD No. 1 Relay Holder

      for 2GR-FKS


      1. Disconnect A79 No. 1 heated windshield defroster (windshield glass) connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 1 relay holder terminal-5 - A79-2 (B) Always Below 1 Ω
        HWD NO. 1 relay holder terminal-5 or A79-2 (B) - Body ground Always 10 kΩ higher
    2. B005PEGC03
      *a HWD No. 1 Relay Holder

      for 8AR-FTS


      1. Disconnect A79 No. 1 heated windshield defroster (windshield glass) connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 1 relay holder terminal-5 - A79-2 (B) Always Below 1 Ω
        HWD NO. 1 relay holder terminal-5 or A79-2 (B) - Body ground Always 10 kΩ higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HARNESS OR CONNECTOR

    OK

  14. CHECK WIRE HARNESS AND CONNECTOR (NO. 1 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS) - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A79-1 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE WINDSHIELD GLASS

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. INSPECT HWD NO. 2 RELAY


    1. Inspect the HWD NO. 2 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE HWD NO. 2 RELAY

    OK

  16. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - BATTERY)


    1. B005LKOC05
      *a HWD No. 2 Relay Holder

      for 2GR-FKS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        HWD NO. 2 relay holder terminal-3 - Body ground Always 11 to 14 V
    2. B005PEGC05
      *a HWD No. 2 Relay Holder

      for 8AR-FTS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        HWD NO. 2 relay holder terminal-3 - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - HWD NO. 3 RELAY)


    1. B005LKOC06
      *a HWD No. 2 Relay Holder
      *b HWD No. 3 Relay Holder

      for 2GR-FKS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-5 - HWD NO. 2 relay holder terminal-2 Always Below 1 Ω
        HWD NO. 3 relay holder terminal-5 or HWD NO. 2 relay holder terminal-2 - Body ground Always 10 kΩ higher
    2. B005PEGC06
      *a HWD No. 2 Relay Holder
      *b HWD No. 3 Relay Holder

      for 8AR-FTS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 3 relay holder terminal-5 - HWD NO. 2 relay holder terminal-2 Always Below 1 Ω
        HWD NO. 3 relay holder terminal-5 or HWD NO. 2 relay holder terminal-2 - Body ground Always 10 kΩ higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  18. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - BODY GROUND)


    1. B005LKOC05
      *a HWD No. 2 Relay Holder

      for 2GR-FKS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 2 relay holder terminal-1 - Body ground Always Below 1 Ω
    2. B005PEGC05
      *a HWD No. 2 Relay Holder

      for 8AR-FTS


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 2 relay holder terminal-1 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  19. CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - NO. 2 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS))


    1. B005LKOC05
      *a HWD No. 2 Relay Holder

      for 2GR-FKS


      1. Disconnect A78 No. 2 heated windshield defroster (windshield glass) connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 2 relay holder terminal-5 - A78-2 (B) Always Below 1 Ω
        HWD NO. 2 relay holder terminal-5 or A78-2 (B) - Body ground Always 10 kΩ higher
    2. B005PEGC05
      *a HWD No. 2 Relay Holder

      for 8AR-FTS


      1. Disconnect A78 No. 2 heated windshield defroster (windshield glass) connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        HWD NO. 2 relay holder terminal-5 - A78-2 (B) Always Below 1 Ω
        HWD NO. 2 relay holder terminal-5 or A78-2 (B) - Body ground Always 10 kΩ higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  20. CHECK WIRE HARNESS AND CONNECTOR (NO. 2 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS) - BODY GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A78-1 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE WINDSHIELD GLASS

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR