POWER BACK DOOR SYSTEM, Diagnostic DTC:B222A

DTC Code DTC Name
B222A PBD Touch Sensor LH Circuit

DESCRIPTION

This DTC is stored when the multiplex network door ECU detects a malfunction in the power back door sensor assembly LH touch sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
B222A PBD Touch Sensor LH Circuit Multiplex network door ECU detects power back door sensor assembly LH touch sensor malfunction

  • Multiplex network door ECU

  • Power back door sensor assembly LH

  • Harness or connector

WIRING DIAGRAM

B005QGCE10
*a Power Back Door Sensor Assembly LH
*b Multiplex Network Door ECU

CAUTION / NOTICE / HINT

Note

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click here

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Back Door > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > Back Door > Trouble Codes
      OK
      DTC B222A is not output
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Back Door / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Back Door > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      PBD Touch Sensor (Left) Power back door sensor assembly LH signal OFF, ON or Open

      OFF: Power back door sensor assembly LH not pressed

      ON: Power back door sensor assembly LH pressed

      Open: Power back door sensor assembly LH circuit open

      		 -

      Body Electrical > Back Door > Data List
      Tester Display
      PBD Touch Sensor (Left)
      Result
      Result Proceed to
      On the GTS screen, ON or OFF is displayed accordingly A
      On the GTS screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH B

    A

    REPLACE MULTIPLEX NETWORK DOOR ECU Click here

    B

  3. INSPECT POWER BACK DOOR SENSOR ASSEMBLY LH


    1. Remove the power back door sensor assembly LH.

      Click here

    2. Inspect the power back door sensor assembly LH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR SENSOR ASSEMBLY LH)


    1. Disconnect the Z16 multiplex network door ECU connector.

    2. Disconnect the Z3 power back door sensor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Z16-26 (OSL) - Z3-1 (OSL) Always Below 1 Ω
      Z16-24 (OSE) - Z3-2 (OSLE) Always Below 1 Ω
      Z16-26 (OSL) or Z3-1 (OSL) - Body ground Always 10 kΩ or higher
      Z16-24 (OSE) or Z3-2 (OSLE) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MULTIPLEX NETWORK DOOR ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR