DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door, Main Body or Entry&Start / Data List.
Read the Data List according to the display on the GTS
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock Status | Back door condition signal | Lock or Unlock | Lock: Back door locked Unlock: Back door unlocked |
- |
| Half Latch SW | Half-latch switch signal | ON or OFF | ON: Back door lock motor in open latch position OFF: Back door lock motor in full latch or half latch position |
* |
| Closer Position SW | Position switch signal | ON or OFF | ON: Back door lock assembly (position switch) on OFF: Back door lock assembly (position switch) off |
* |
| Pawl Position Switch | Pawl switch signal | ON or OFF | ON: Back door lock assembly (pawl switch) on OFF: Back door lock assembly (pawl switch) off |
* |
| Courtesy SW | Latch courtesy switch signal | ON or OFF | ON: Back door open OFF: Back door closed |
* |
| PBD Touch Sensor (Right) | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor (Left) | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| PBD Main SW | Power back door ON/OFF signal | ON or OFF | Customize setting displayed | - |
| PBD Close SW | Back door control switch signal | ON or OFF | ON: Back door control switch pressed OFF: Back door control switch not pressed |
- |
| IG SW | Engine switch signal | ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off |
"OFF" is also displayed for this item when the engine switch is on (ACC). |
| PBD Position (3/4-Open) | Load signal detected during back door closing operation (3/4 - Open) | Caution or OK | Caution: Load detected between back door 3/4 and fully open position during back door closing operation OK: No load detected between back door 3/4 and fully open position during back door closing operation |
- |
| PBD Position (2/4-3/4) | Load signal detected during back door closing operation (2/4 - 3/4) | Caution or OK | Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation |
- |
| PBD Position (1/4-2/4) | Load signal detected during back door closing operation (1/4 - 2/4) | Caution or OK | Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation |
- |
| PBD Position (Close-1/4) | Load signal detected during back door closing operation (Close - 1/4) | Caution or OK | Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation OK: No load detected between back door fully closed and 1/4 open position during back door closing operation |
- |
| Closed Position Initialization | Back door fully closed position memorized signal | Not Initialized or Initialized | Not Initialized: Back door fully closed position not memorized Initialized: Back door fully closed position memorized |
- |
| PBD SW Operation | Power back door switch operation | 0.0 s or 0.8 s | Customize setting displayed | - |
| PBD Assist Open Operation | Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. | OFF or ON | Customize setting displayed | - |
| PBD Assist Close Operation | Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. | OFF or ON | Customize setting displayed | - |
| Door Unlock with 1 Motion. | Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch | Back Door or ALL DOORS | Customize setting displayed | - |
| One Motion | Function that operates the power back door by pressing the transmitter switch (electrical key transmitter sub-assembly) when the back door is locked or unlocked. | OFF, 1 Op, 2 Op, 0.8s or Not Use | Customize setting displayed | - |
| One Motion with Unlock Door | Function that operates the power back door by pressing the transmitter switch (electrical key transmitter sub-assembly) when the back door is locked or unlocked. | OFF, Not Use, 2 Op or 0.8s | Customize setting displayed | - |
| Power Back Door Opening Adjust | Function that changes the position that the power back door stops during an open operation. | Min, Small, Middle, Large or Max | Customize setting displayed | - |
| Emblem Sensor | Rear emblem sensor assembly connection status | Without or With | Without: Rear emblem sensor assembly not connected With: Rear emblem sensor assembly connected |
- |
| Emblem Sensor Detection | Rear emblem sensor assembly detection status | OFF or ON | OFF: Rear emblem sensor assembly not detecting a hand ON: Rear emblem sensor assembly detecting a hand |
- |
| PBD/Emblem Sensor Function | Function that enables/disables the power back door and rear emblem sensor assembly. | PBD OFF/Emblem OFF, PBD ON/Emblem OFF or PBD ON/Emblem ON | Customize setting displayed | - |
| PBD Buzzer Volume Adjust | Function that changes the volume setting of the power back door buzzer. | Small, Middle or Large | Customize setting displayed | - |
| PBD Buzzer Function | Function that changes the power back door buzzer setting. | OFF, Start Buzzer ON/In Operation Buzzer OFF, Start Buzzer OFF/In Operation Buzzer ON or ON | Customize setting displayed | - |
| PBD Buzzer Tone | Function that changes the sounding pattern of the power back door buzzer. | Pattern A, Pattern B or Pattern C | Customize setting displayed | - |
| Emblem Sensor Detection Sensitivity | Function that changes the sensitivity of the rear emblem sensor assembly. | Low, Middle or High | Customize setting displayed | - |
| Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Frequent Contact/Calibration Failure) | Number of times emblem sensor changed to sensitivity reduction mode (frequent contact/calibration failure) | None, Low, Middle or High | None: Never Low: 1 to 10 times Middle: 11 to 50 times High: 51 times or more |
- |
| Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Power Saving) | Number of times emblem sensor changed to sensitivity reduction mode (power saving) | None, Low, Middle or High | None: Never Low: 1 to 10 times Middle: 11 to 50 times High: 51 times or more |
- |
| Emblem Sensor Sensitivity Drop Frequency (Disturbance Factor) | Number of times emblem sensor sensitivity decreased (wave interference) | None, Low, Middle or High | None: Never Low: 1 to 10 times Middle: 11 to 50 times High: 51 times or more |
- |
| Emblem Sensor Sensitivity Drop Frequency (Foreign Matter Adhering) | Number of times emblem sensor sensitivity decreased (adherence of foreign matter) | None, Low, Middle or High | None: Never Low: 1 to 10 times Middle: 11 to 50 times High: 51 times or more |
- |
| #Codes | Number of DTCs | Min.: 0, Max.: 255 | Number of output DTCs | - |
*: Refer to Power Back Door Operation Timing Chart.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open | Back door lock | Permit or Prohibit | Permit: Back door unlocked Prohibit: Back door locked |
- |
| Back Door Open SW | Combination switch assembly signal | ON or OFF | ON: Combination switch assembly on OFF: Combination switch assembly off |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door opener switch assembly (open switch) signal | ON or OFF | ON: Back door opener switch assembly (open switch) on OFF: Back door opener switch assembly (open switch) off |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door / Active Test.
Perform the Active Test according to the display on the GTS
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Latch Release | Latch release operation | ON or OFF | - |
| PBD Open/Close | Power back door motor operation | Forward, Reverse or OFF | - |
| PBD Buzzer | Power back door warning buzzer sound | ON or OFF | - |
| PBD Close SW Light | Close switch light operation | ON or OFF | - |