NAVIGATION SYSTEM AVC-LAN Circuit

DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.

If a short to +B or short to ground occurs in an AVC-LAN communication line, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

B005OZ1E02

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

Tech Tips

The radio receiver assembly is the master unit.

PROCEDURE


  1. INSPECT RADIO RECEIVER ASSEMBLY


    1. Remove the radio receiver assembly.

      Click here

    2. B005P5TC03
      *A w/ Panoramic View Monitor System
      *a

      Component without harness connected

      (Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω
      7 (TX1+) - 8 (TX1-)* Always 60 to 80 Ω

      • *: w/ Panoramic View Monitor System

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)


    1. Disconnect the J50 radio receiver assembly connector.

    2. Disconnect the J56 multi-display assembly connector (for 8 Inch Display).

      Disconnect the J137 accessory meter assembly connector (for 12.3 Inch Display).

    3. Disconnect the J73 parking assist ECU connector (w/ Panoramic View Monitor System).

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition

      J50-45 (TX3+) - J56-7 (TX+)*1

      J50-45 (TX3+) - J137-7 (TX+)*2

      		 Always Below 1 Ω

      J50-46 (TX3-) - J56-19 (TX-)*1

      J50-46 (TX3-) - J137-19 (TX-)*2

      		 Always Below 1 Ω
      J50-7 (TX1+) - J73-10 (TX+)*3 Always Below 1 Ω
      J50-8 (TX1-) - J73-9 (TX-)*3 Always Below 1 Ω

      J50-45 (TX3+) or J56-7 (TX+) - Body ground*1

      J50-45 (TX3+) or J137-7 (TX+) - Body ground*2

      		 Always 10 kΩ or higher

      J50-46 (TX3-) or J56-19 (TX-) - Body ground*1

      J50-46 (TX3-) or J137-19 (TX-) - Body ground*2

      		 Always 10 kΩ or higher
      J50-7 (TX1+) or J73-10 (TX+) - Body ground*3 Always 10 kΩ or higher
      J50-8 (TX1-) or J73-9 (TX-) - Body ground*3 Always 10 kΩ or higher

      • *1: for 8 Inch Display

        *2: for 12.3 Inch Display

        *3: w/ Panoramic View Monitor System

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT MALFUNCTIONING PARTS


    1. Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

      Tech Tips


      • Check all slave units.

      • If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.

      OK
      Master unit returns to normal.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MALFUNCTIONING PARTS

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here