NAVIGATION SYSTEM, Diagnostic DTC:B1579

DTC Code DTC Name
B1579 Voice Recognition Microphone Disconnected

DESCRIPTION

The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost

  • Telephone microphone assembly

  • Telematics transceiver*

  • Radio receiver assembly

  • Harness or connector

*: w/ Telematics Transceiver for G-BOOK

WIRING DIAGRAM

B005NR5E03

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. INSPECT RADIO RECEIVER ASSEMBLY


    1. B005QA0C33
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J50-48 (MIN-) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  2. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/ Telematics Transceiver for G-BOOK A
      w/o Telematics Transceiver or w/ Telematics Transceiver except G-BOOK B

    B

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)


    1. Disconnect the J62 telematics transceiver connector.

    2. Disconnect the U15 telephone microphone assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J62-35 (MCI-) - U15-4 (MCO-) Always Below 1 Ω
      J62-35 (MCI-) or U15-4 (MCO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)


    1. Disconnect the J50 radio receiver assembly connector.

    2. Disconnect the J62 telematics transceiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J50-48 (MIN-) - J62-19 (MCO-) Always Below 1 Ω
      J50-48 (MIN-) or J62-19 (MCO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)


    1. Disconnect the J50 radio receiver assembly connector.

    2. Disconnect the U15 telephone microphone assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J50-49 (SNS2) - U15-3 (SNS2) Always Below 1 Ω
      J50-49 (SNS2) or U15-3 (SNS2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT TELEMATICS TRANSCEIVER


    1. Reconnect the J62 telematics transceiver connector.

    2. Reconnect the J50 radio receiver assembly connector.

    3. B005NLSC13
      *a

      Component with harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J62-35 (MCI-) - Body ground Always Below 1 Ω

    4. Proceed to the next step based on the inspection result.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 8 Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)


    1. Disconnect the J50 radio receiver assembly connector.

    2. Disconnect the U15 telephone microphone assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J50-49 (SNS2) - U15-3 (SNS2) Always Below 1 Ω
      J50-48 (MIN-) - U15-4 (MCO-) Always Below 1 Ω
      J50-49 (SNS2) or U15-3 (SNS2) - Body ground Always 10 kΩ or higher
      J50-48 (MIN-) or U15-4 (MCO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT TELEPHONE MICROPHONE ASSEMBLY


    1. Remove the telephone microphone assembly.

      Click here

    2. B005ODSC04
      *a

      Component without harness connected

      (Telephone Microphone Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (SNS2) - 4 (MCO-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here