ELECTRIC PARKING BRAKE SYSTEM Electric Parking Brake does not Operate

WIRING DIAGRAM

A01VTITE02

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Before disconnecting connectors or fuses, turn the engine switch off and wait 20 seconds or more.

  • When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks (red) when the engine switch is first turned on (IG).

Tech Tips

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.

PROCEDURE


  1. VEHICLE OPERATION CHECK


    1. Start the engine and move the shift lever to D. Then depress the brake pedal and pull the electric parking brake switch assembly to the lock side for 1 second. Check the parking brake indicator light (red) operation.

    2. Release the brake pedal and check that the vehicle does not move.

    3. Depress the brake pedal and push the electric parking brake switch assembly to the release side for 1 second. Check the parking brake indicator light (red) operation.

    4. Release the brake pedal and check that the vehicle moves.

      Result
      Result Proceed to
      Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
      Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
      Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C

    B

    INSPECT REAR BRAKE

    C

    CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)) Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (PKB LIGHT)


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test.

    6. Perform the Active Test according to the display on the GTS.


      Chassis > ABS/VSC/TRC/EPB > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      PKB Light Parking brake indicator light (red) ON or OFF

      • Vehicle stopped

      • Engine switch on (IG)

      • Parking brake released

      Chassis > ABS/VSC/TRC/EPB > Active Test
      Tester Display
      PKB Light
      OK
      The parking brake indicator light turns on (red) or off in accordance with the Active Test operation.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)


    1. Turn the engine switch off.

    2. Disconnect the A41 skid control ECU (brake actuator assembly) connector.

    3. Disconnect the J10 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A41-15 (TX) - J10-5 (EPB) Always Below 1 Ω
      A41-15 (TX) or J10-5 (EPB) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO METER / GAUGE SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))


    1. Turn the engine switch off.

    2. B005MOKC08
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Disconnect the A41 skid control ECU (brake actuator assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A41-45 (IG1) - Body ground Engine switch on (IG)

      11 to 14 V*1

      9.5 to 14 V*2

      • *1: w/o Stop and Start System

      • *2: w/ Stop and Start System

      Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C

    A

    REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) Click here

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    GO TO STOP AND START SYSTEM Click here