FRONT DRIVE SHAFT ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | FRONT FENDER APRON SEAL LH | *2 | FRONT WHEEL OPENING EXTENSION PAD LH |
| *3 | NO. 3 ENGINE UNDER COVER | - | - |
ILLUSTRATION
| *A | w/o AVS | *B | w/ AVS |
| *1 | FRONT AXLE SHAFT NUT | *2 | FRONT DRIVE SHAFT ASSEMBLY |
| *3 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY | *4 | FRONT SPEED SENSOR |
| *5 | FRONT STABILIZER LINK ASSEMBLY | *6 | TIE ROD ASSEMBLY |
| *7 | FRONT AXLE ASSEMBLY | *8 | COTTER PIN |
| *9 | FRONT FLEXIBLE HOSE | *10 | FRONT SKID CONTROL SENSOR WIRE |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Do not apply lubricants to the threaded parts |
 |
Toyota Body Grease W | - | - |
ILLUSTRATION
| *A | for 2WD | *B | for AWD |
| *C | for 8AR-FTS | *D | for 2GR-FKS |
| *1 | FRONT DRIVE SHAFT ASSEMBLY LH | *2 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *3 | FRONT DRIVE SHAFT HOLE SNAP RING | *4 | BEARING BRACKET HOLE SNAP RING |
| *5 | NO. 1 DRIVE SHAFT BEARING BRACKET SETTING BOLT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
ATF WS |  |
Toyota genuine differential gear oil LT 75W-85 GL-5 or equivalent |
ILLUSTRATION
| *A | for LH Side | - | - |
| *1 | FRONT AXLE INBOARD JOINT BOOT | *2 | FRONT AXLE INBOARD JOINT BOOT CLAMP |
| *3 | FRONT AXLE OUTBOARD JOINT BOOT | *4 | FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
| *5 | FRONT DRIVE INBOARD JOINT ASSEMBLY | *6 | FRONT DRIVE SHAFT DAMPER |
| *7 | FRONT DRIVE SHAFT DAMPER CLAMP | *8 | FRONT DRIVE SHAFT DUST COVER LH |
| *9 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP | *10 | FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP |
| *11 | SHAFT SNAP RING | *12 | TRIPOD JOINT |
| *13 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY | *14 | FRONT AXLE INBOARD JOINT GROMMET |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for 2WD RH Side | *B | w/ Cover |
| *1 | FRONT AXLE INBOARD JOINT BOOT | *2 | FRONT AXLE INBOARD JOINT BOOT CLAMP |
| *3 | FRONT AXLE OUTBOARD JOINT BOOT | *4 | FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
| *5 | FRONT DRIVE INBOARD JOINT ASSEMBLY | *6 | FRONT DRIVE SHAFT BEARING |
| *7 | FRONT DRIVE SHAFT DAMPER | *8 | FRONT DRIVE SHAFT DAMPER CLAMP |
| *9 | FRONT DRIVE SHAFT DUST COVER | *10 | FRONT DRIVE SHAFT DUST COVER RH |
| *11 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP | *12 | FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP |
| *13 | SHAFT SNAP RING | *14 | TRIPOD JOINT |
| *15 | DRIVE SHAFT HOLE SNAP RING | *16 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY |
| *17 | FRONT AXLE INBOARD JOINT GROMMET | - | - |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for AWD RH Side | *B | w/ Drive Shaft Damper |
| *1 | FRONT AXLE INBOARD JOINT BOOT | *2 | FRONT AXLE INBOARD JOINT BOOT CLAMP |
| *3 | FRONT DRIVE INBOARD JOINT ASSEMBLY | *4 | FRONT DRIVE SHAFT BEARING |
| *5 | FRONT DRIVE SHAFT DAMPER | *6 | FRONT DRIVE SHAFT DAMPER CLAMP |
| *7 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP | *8 | SHAFT SNAP RING |
| *9 | TRIPOD JOINT | *10 | DRIVE SHAFT HOLE SNAP RING |
| *11 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY | *12 | FRONT AXLE INBOARD JOINT GROMMET |
| ● | Non-reusable part | - | - |