AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P27567F

DTC Code DTC Name
P27567F Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off

DESCRIPTION

The ECM controls the shift solenoid valve SLU using a predetermined current, and performs lock-up and flex lock-up control.

The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical malfunctions of the shift solenoid valve SLU, transmission valve body assembly and torque converter assembly.

A01VVSIE01
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P27567F Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


    SLU stuck ON malfunction:

  1. Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the ECM sends a lock-up off request (no malfunctions are detected in the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and SLU, transmission revolution sensors (NT, NC3, NC), engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle, crankshaft position sensor or CAN2)

  2. The difference between the input turbine speed (NT) and the engine speed (NE) is less than 35 rpm

  3. 1.8 seconds or more

  4. 2-trip detection logic


    SLU stuck OFF malfunction:

  1. Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the ECM sends a lock-up on request (no malfunctions are detected in the shift solenoid valves SL1, SL2, SL3, SL4, SL5, S1 and SLU, transmission revolution sensors (NT, NC3, NC), engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle, crankshaft position sensor or CAN2)

  2. The difference between the input turbine speed (NT) and the engine speed (NE) is 70 rpm or more

  3. 3.5 seconds or more

  4. 2-trip detection logic

  • Shift solenoid valve SLU

  • Transmission valve body assembly

  • Torque converter assembly

  • Automatic transaxle assembly

 Comes on DTC stored

SAE Code:

P2757

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the transmission revolution sensor (NT, NC), engine speed, engine load, engine temperature, vehicle speed, ATF temperature and gear selection signals. The ECM determines the lock-up status of the torque converter assembly by comparing the engine speed (NE) to the transmission revolution sensor (NT) signal. The ECM calculates the actual gear by comparing the transmission revolution sensor (NT) signal to the transmission revolution sensor (NC) signal. When conditions are appropriate, the ECM requests "lock-up" by applying voltage to the shift solenoid valve SLU. When the shift solenoid valve SLU is turned on, pressure is applied to the lock-up relay valve and locks the torque converter assembly.

If the ECM does not detect lock-up after lock-up has been requested or if it detects lock-up when it is not requested, it interprets this as a malfunction of the shift solenoid valve SLU, illuminates the MIL and stores this DTC.

Tech Tips

Example:

When any of the following is met, the system judges it as a malfunction.


  • There is a difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter assembly when the ECM commands lock-up. (Engine speed is at least 70 rpm more than input turbine speed.)

  • There is no difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter assembly when the ECM commands lock-up off. (The difference between engine speed and input turbine speed is less than 35 rpm.)

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Perform the Lock-up Function inspection in Road Test.

    Click here

  2. Turn the engine switch off.

  3. Perform step (1) again.

  4. Check for DTCs again.

    Click here

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P27567F)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    5. Read the DTCs using the GTS.

      Result
      Result Proceed to
      Only DTC P27567F is output A
      DTC P27567F and other DTCs are output B

      Tech Tips


      • If any DTCs other than P27567F are output, perform troubleshooting for those DTCs first.

      • If a shift solenoid valve is stuck ON or OFF, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.


    B

    GO TO DTC CHART Click here

    A

  2. INSPECT SHIFT SOLENOID VALVE SLU


    1. A01VVIWC67
      *a

      Component without harness connected

      (Shift Solenoid Valve SLU)

      Remove the shift solenoid valve SLU.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Shift solenoid valve SLU connector terminal 1 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SHIFT SOLENOID VALVE SLU Click here

    OK

  3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY


    1. Inspect the transmission valve body assembly.

      Click here

      OK
      There is no foreign matter on each valve and they operate smoothly.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY Click here

    OK

  4. INSPECT TORQUE CONVERTER ASSEMBLY


    1. Inspect the torque converter assembly.

      Click here

      OK
      The torque converter assembly is normal.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE TORQUE CONVERTER ASSEMBLY Click here

    OK

  5. REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY


    1. Repair or replace the automatic transaxle assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here