DIFFERENTIAL OIL SEAL REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment

Perform the following procedures in the order shown:


  1. Clearing zero point calibration data and system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctioning

  • DTCs are output

  • Slip indicator light illuminated

  • ABS warning light illuminated

  • Theft deterrent system (tilt sensor) (w/ TFT Meter Type)

Click here

PROCEDURE


  1. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

    Click here

  2. REMOVE NO. 3 ENGINE UNDER COVER

    Click here

  3. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  4. DRAIN AUTOMATIC TRANSAXLE FLUID


    1. B005LSG

      Remove the refill plug and gasket from the automatic transaxle case sub-assembly.

    2. B005LJ4

      Using a T40 "TORX" socket wrench, remove the drain plug and O-ring from the transaxle housing.

    3. B005N0G

      Using a 17 mm straight hexagon wrench, remove the overflow plug and O-ring from the transaxle housing and drain the automatic transaxle fluid.

    4. Using a 17 mm straight hexagon wrench, install a new O-ring and the overflow plug to the transaxle housing.

      Torque:
      47 N*m  { 479 kgf*cm, 35 ft.*lbf }

    5. Using a T40 "TORX" socket wrench, temporarily install the O-ring and drain plug to the transaxle housing.

      Tech Tips

      Reuse the old O-ring as the drain plug will be removed again to adjust the automatic transaxle fluid level.

    6. Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

      Tech Tips

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

  5. REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  6. REMOVE DRIVE SHAFT BEARING BRACKET

    Click here

  7. REMOVE FRONT DRIVE SHAFT OIL SEAL LH


    1. B005MWEN01

      Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

      SST
      09308-00010

      Note

      Be careful not to damage the automatic transaxle case sub-assembly.

  8. REMOVE FRONT DRIVE SHAFT OIL SEAL RH


    1. B005LL6N01

      Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

      SST
      09308-00010

      Note

      Be careful not to damage the transaxle housing.

  9. INSTALL FRONT DRIVE SHAFT OIL SEAL RH


    1. B005OSPC01
      *a Depth

      Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

      SST
      09316-60011   ( 09316-00011 )
      09950-70010   ( 09951-07150 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front drive shaft oil seal RH is installed in the correct direction.

      • Do not damage the lip of the front drive shaft oil seal RH.

    2. Coat the lip of the front drive shaft oil seal RH with MP grease.

  10. INSTALL FRONT DRIVE SHAFT OIL SEAL LH


    1. B005L4EC01
      *a Depth

      Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

      SST
      09316-10010
      09950-70010   ( 09951-07100 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front drive shaft oil seal LH is installed in the correct direction.

      • Do not damage the lip of the front drive shaft oil seal LH.

    2. Coat the lip of the front drive shaft oil seal LH with MP grease.

  11. INSTALL DRIVE SHAFT BEARING BRACKET

    Click here

  12. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  13. ADJUST AUTOMATIC TRANSAXLE FLUID

    Click here

  14. INSPECT FOR FLUID LEAK

  15. INSTALL FRONT FENDER APRON SEAL LH

    Click here

  16. INSTALL NO. 3 ENGINE UNDER COVER

    Click here

  17. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

    Click here