TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    Note

    Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.


    1. Pass the transmission control cable assembly from the cabin to the engine compartment.

    2. Install the transmission control cable assembly with the 3 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    3. Return the floor carpet to its original position.

    4. B005OVU

      Engage the 2 clamps.

    5. Install a new clip to the No. 1 transmission control cable bracket.

    6. B005ODOC10
      *1 Transmission Control Cable Assembly
      *2 No. 1 Transmission Control Cable Bracket
      *a Claw (A)
      *b Claw (B)

      Connect the transmission control cable assembly to the No. 1 transmission control cable bracket.

      Note


      • Make sure that the claws (A) of the clip are securely engaged in the grooves of the No. 1 transmission control cable bracket.

      • Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.

    7. B005MBIC01
      *a P Position
      *b N Position

      Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

    8. Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the shift lever is in neutral.

    9. B005LQJC31
      *a Slider
      *b Lock Piece
      *c Slide
      *d Pull

      Slide the slider of the transmission control cable assembly and pull the lock piece outward as shown in the illustration.

    10. Engage the 2 claws to connect the transmission control cable assembly to the transmission floor shift assembly.

      Note

      Make sure that the transmission control cable assembly is securely connected.

    11. B005MHOC01
      *a Lock Piece
      *b Adjuster Case

      Connect the transmission control cable assembly to the transmission floor shift assembly.

      Note


      • Check that the lock piece is pulled out.

      • Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

      • Connect the transmission control cable assembly so that the lock piece faces the driver side.

    12. B005MYVC01
      *a Lock Piece
      *b Push in
      *c Adjuster Case

      Push the lock piece into the adjuster case.

      Note


      • Make sure that the park/neutral position switch assembly and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

      • After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.

  2. INSTALL FRONT NO. 2 CONSOLE BOX INSERT

    Click here

  3. INSTALL FRONT NO. 1 CONSOLE BOX INSERT

    Click here

  4. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  6. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

    Click here

  7. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  8. INSTALL BATTERY

    Click here

  9. INSTALL INLET AIR CLEANER ASSEMBLY

    Click here

  10. INSTALL COOL AIR INTAKE DUCT SEAL

    Click here

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  12. INSPECT SHIFT LEVER POSITION

    Click here