AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P271313

DTC Code DTC Name
P271313 Pressure Control Solenoid "D" Circuit Open

DESCRIPTION

Refer to DTC P27137F.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P271313 Pressure Control Solenoid "D" Circuit Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. Engine is running

  2. Shift solenoid valve SLT circuit is open or shorted

  3. 1 second

  4. 1-trip detection logic

  • Shift solenoid valve SLT

  • Transmission wire

  • Harness and connector

  • ECM

 Comes on DTC stored

SAE Code:

P2716

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

WIRING DIAGRAM

A01VVERE77
*a Shift Solenoid Valve SLT
*b Transmission Wire

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Start the engine.

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT) - ECM)


    1. Disconnect the D2 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D2-67 (SLT+) - D2-37 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      D2-67 (SLT+) or D2-37 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) Click here

    OK

  2. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the D56 transmission wire connector.

    2. Disconnect the D2 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D56-3 (SLT+) - D2-67 (SLT+) Always Below 1 Ω
      D56-4 (SLT-) - D2-37 (SLT-) Always Below 1 Ω
      D56-3 (SLT+) or D2-67 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
      D56-4 (SLT-) or D2-37 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  4. INSPECT SHIFT SOLENOID VALVE SLT


    1. A01VVIWC67
      *a

      Component without harness connected

      (Shift Solenoid Valve SLT)

      Remove the shift solenoid valve SLT.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Shift solenoid valve SLT connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

    NG

    REPLACE SHIFT SOLENOID VALVE SLT Click here