AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P098712

DTC Code DTC Name
P098712 Transmission Fluid Pressure Sensor/Switch "E" Circuit Short to Battery

DESCRIPTION

The No. 3 ATF pressure switch is installed in the lock-up solenoid ATF output passage and is used to detect malfunctions of the lock-up solenoid.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P098712 Transmission Fluid Pressure Sensor/Switch "E" Circuit Short to Battery

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. Lock-up is not operating.

  2. Both of the following conditions are met:


    • The No. 3 ATF pressure switch is ON when lock-up does not occur.

    • Lock-up does not occur when solenoid (SLU) valve is requested to turn off in the lock-up range.

  3. 1.2 seconds

  4. 2-trip detection logic

  • Harness and connector

  • Wiring harness connector

  • No. 3 ATF pressure switch (ATF temperature sensor assembly)

  • Transmission wire

  • ECM

 Comes on DTC stored

SAE Code:

P0990

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC if it detects that the No. 3 ATF pressure switch is OFF with the lock-up solenoid ON or if it detects that the No. 3 ATF pressure switch is ON with the lock-up solenoid OFF.

WIRING DIAGRAM

Refer to DTC P071011.

Click here

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Perform the Lock-up Function inspection in Road Test.

    Click here

  2. Turn the engine switch off.

  3. Perform step (1) again.

  4. Check for DTCs again.

    Click here

PROCEDURE


  1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P098712)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    5. Read the DTCs using the GTS.

      Result
      Result Proceed to
      Only DTC P098712 is output A
      DTC P098712 and other DTCs are output B

      Tech Tips

      If any DTCs other than P098712 are output, perform the troubleshooting for those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK HARNESS AND CONNECTOR (NO. 3 ATF PRESSURE SWITCH CIRCUIT)


    1. Disconnect the D1 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D1-85 (TPS3) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)


    1. Disconnect the D57 wiring harness connector connector.

    2. Disconnect the D1 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D57-10 (TPS3) or D1-85 (TPS3) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT TRANSMISSION WIRE


    1. A01VTI7C11
      *a

      Component without harness connected

      (Transmission Wire)

      Remove the wiring harness connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-10 (TPS3) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE WIRING HARNESS CONNECTOR Click here

    NG

  5. INSPECT NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY)


    1. A01VWTYC13
      *a

      Component without harness connected

      (ATF Temperature Sensor Assembly)

      Disconnect the ATF temperature sensor assembly connector.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      TPS3 - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TRANSMISSION WIRE Click here

    NG

    REPLACE NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY) Click here