REAR DOOR WINDOW FRAME MOULDING INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

   
   

   1. Engage the claws and temporarily install the rear door window frame moulding sub-assembly to the door frame.

      

   2. Using an air riveter or a hand riveter with a nose piece, install 8 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note

      
      

      • Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      
      

      • 

        *a	Riveter
        *b	Incorrect

        Confirm that the rivets are seated properly against the vehicle body.

      
      

      • Do not tilt the riveter when installing the rivet to the vehicle body.

      

      *a	Riveter
      *b	Mandrel
      *c	Incorrect

2. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

   Tech Tips

   When installing the rear door front window frame moulding, heat the door frame and rear door front window frame moulding using an infrared light.

   Heating Temperature
   Item Temperature Door Frame 40 to 60°C (104 to 140°F) Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

   Note

   Do not heat the door frame and rear door front window frame moulding excessively.

   
   

   1. Clean the door frame surface.

      
      

      1. Using an infrared light, heat any adhesive remaining on the door frame.

      2. Using a piece of cloth, rub the double-sided tape off the door frame.

         Note

         
         

         • Installing the rear door front window frame moulding while old double-sided tape remains can cause adhesion failure.

         • Using a screwdriver or similar tool to remove the old tape can damage the surface and cause adhesion failure.

      3. Using a non-residue solvent, clean the attachment surface.

   2. Using an infrared light, heat the door frame and rear door front window frame moulding.

   3. Remove the peeling paper from a new rear door front window frame moulding.

      Tech Tips

      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

   4. 

      *a	Double-sided Tape
      *b	Butyl Tape
      	Install in this Direction (1)
      	Install in this Direction (2)

      Engage the guide and clip to install the rear door front window frame moulding as shown in the illustration.

      Note

      Press the rear door front window frame moulding firmly to install it.

3. INSTALL REAR DOOR WEATHERSTRIP

   
   

   1. Install the upper part of the rear door weatherstrip.

4. INSTALL REAR DOOR FRONT BELT MOULDING END COVER

   Tech Tips

   When installing the rear door front belt moulding end cover, heat the door frame and rear door front belt moulding end cover using an infrared light.

   Heating Temperature
   Item Temperature Door Frame 40 to 60°C (104 to 140°F) Rear Door Front Belt Moulding End Cover 20 to 30°C (68 to 86°F)

   Note

   Do not heat the door frame and rear door front belt moulding end cover excessively.

   
   

   1. Clean the door frame surface.

      
      

      1. Using an infrared light, heat any adhesive remaining on the door frame.

      2. Using a piece of cloth, rub the double-sided tape off the door frame.

         Note

         
         

         • Installing the rear door front window frame moulding while old double-sided tape remains can cause adhesion failure.

         • Using a screwdriver or similar tool to remove the old tape can damage the surface and cause adhesion failure.

      3. Using a non-residue solvent, clean the attachment surface.

   2. Using an infrared light, heat the door frame and rear door front belt moulding end cover.

   3. Remove the peeling paper from a new rear door front belt moulding end cover.

      Tech Tips

      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

   4. 

      *a	Double-sided Tape
      	Install in this Direction

      Engage the clips to install the rear door front belt moulding end cover as shown in the illustration.

      Note

      Press the rear door front belt moulding end cover firmly to install it.

5. INSTALL REAR DOOR QUARTER WINDOW GLASS

   Click here

6. INSTALL REAR DOOR BELT MOULDING

   Click here

7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

   Click here

   Note

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

   Click here

8. INITIALIZE POWER WINDOW CONTROL SYSTEM

   Click here

9. INSPECT POWER WINDOW OPERATION

   Click here