REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear door disassembly/reassembly are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system

Click here

LKA/LDA system

Click here

Pre-crash safety system
Adaptive high beam system
Reset power trunk lid Power trunk lid system

Click here


  • Rear door window regulator sub-assembly

  • Rear door glass sub-assembly

  • Rear door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

  • Catch protection function

Click here

Tech Tips


  • Use the same procedures for both the LH and RH sides.

  • The procedure described below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. B002EBUC01
      B002C8N Remove in this Direction

      Using a molding remover A, disengage the claws to remove the rear door inside handle bezel plug as shown in the illustration.

  4. REMOVE REAR DOOR HOLE COVER


    1. B002DJF

      Remove the rear door hole cover.

  5. REMOVE REAR ARMREST BASE UPPER PANEL SUB-ASSEMBLY


    1. B002D31

      Disengage the clips and claws.

    2. Disconnect the connector to remove the rear armrest base upper panel sub-assembly.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B002ERPC01
      B002D0A Place Hands Here
      B002C8N Remove in this Direction

      Remove the 3 screws.

    2. Disengage the clips as shown in the illustration.

    3. B002F0CC01
      *a Reference Boss
      *b Protective Tape

      Disengage the reference boss in the direction indicated by the arrow in the illustration.

    4. Using a screwdriver with its tip wrapped in protective tape, disengage the claws.

    5. Disconnect each connector.

    6. B002C98C01
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly.

  7. REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Sunshade)


    1. B002CMS

      Remove the 7 screws and rear curtain sub-assembly.

  8. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY

    Click here

  9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. B002E5L

      Remove the 14 screws and rear door inside handle sub-assembly together with the rear door trim ornament sub-assembly and No. 1 interior illumination light assembly.

    2. B002CBF

      Remove the screw.

    3. Disengage the claw to remove the rear door inside handle sub-assembly.

  10. REMOVE REAR DOOR TRIM ORNAMENT SUB-ASSEMBLY


    1. B002CSO

      Disengage the claws to remove the rear door trim ornament sub-assembly from the No. 1 interior illumination light assembly.

  11. REMOVE REAR DOOR COURTESY LIGHT ASSEMBLY

    Click here

  12. REMOVE REAR DOOR TRIM SEAL


    1. B002DIU

      Using a clip remover, disengage the clips to remove the rear door trim seal.

  13. REMOVE NO. 1 REAR DOOR STIFFENER CUSHION


    1. B002CXI

      Remove the No. 1 rear door stiffener cushion.

  14. REMOVE REAR DOOR TRIM COVER


    1. B002ELL

      Disengage the clips to remove the rear door trim cover.

  15. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP


    1. B002CBVC01
      B002C8N Remove in this Direction

      Remove the rear door glass inner weatherstrip as shown in the illustration.

  16. REMOVE REAR SIDE CURTAIN ASSEMBLY (w/ Rear Sunshade)


    1. B002EE8

      Disengage the claws and clips to remove the rear side curtain assembly.

  17. REMOVE REAR DOOR FRAME GARNISH


    1. B002CCP

      Disengage the clips to remove the rear door frame garnish.

  18. REMOVE REAR DOOR ARMREST SET BRACKET


    1. B002CH6

      Remove the 2 screws and rear door armrest set bracket.

  19. REMOVE REAR NO. 2 SPEAKER ASSEMBLY

    Click here

  20. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  21. REMOVE REAR DOOR SERVICE HOLE COVER


    1. B002E9J

      Pull out the rear door lock remote control cable assembly and rear door inside locking cable assembly from the rear door service hole cover and remove the rear door service hole cover.

      Note

      Remove any remaining butyl tape from the rear door panel sub-assembly.

  22. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY


    1. Connect the rear power window regulator switch assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the rear door glass sub-assembly so that the rear door glass channel can be seen.

    4. Disconnect the rear power window regulator switch assembly.

    5. B002DTV

      Partially disengage the rear door glass run as shown in the illustration.

    6. Raise up the rear door weatherstrip and then remove the screw.

    7. B002CCV

      Remove the screw and 2 bolts.

    8. Install the rear door weatherstrip.

    9. B002EI1

      Separate the rear door window rear lower frame sub-assembly together with the rear door glass run as shown in the illustration.

    10. B002CV0

      Remove the rear door window rear lower frame sub-assembly from the rear door glass run.

  23. REMOVE REAR DOOR GLASS RUN


    1. B002EZW

      Remove the rear door glass run.

  24. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. B002ESBC01
      B002C8N Remove in this Direction

      Remove the rear door quarter window glass as shown in the illustration.

  25. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


    1. B002CX4

      Remove the rear door quarter window weatherstrip from the rear door quarter window glass.

  26. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. B002DFE

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  27. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    1. B002CXKC01
      *a Protective Tape
      B002C8N Remove in this Direction

      Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel sub-assembly as shown in the illustration.

  28. REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. B002EZ3C01
      B002C8N Remove in this Direction

      Remove the rear door glass channel filler.

  29. REMOVE REAR DOOR BELT MOULDING

    Click here

  30. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. Disconnect the connector.

    2. B002F0LC01
      *a Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly may fall and cause damage.

    3. Remove the 3 bolts and rear door window regulator sub-assembly.

    4. Remove the temporary bolt from the rear door window regulator sub-assembly.

  31. REMOVE REAR DOOR LOCK ASSEMBLY

    Click here

  32. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

    Click here

  33. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

    Click here

  34. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. B002CS0C01
      B002C8N Remove in this Direction

      Using a T30 "TORX" socket wrench, loosen the screw.

    2. Remove the rear door outside handle cover as shown in the illustration.

  35. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. B002ECLC01
      *a Protective Tape
      B002C8N Remove in this Direction

      Using a screwdriver with its tip wrapped in protective tape, disengage the claws of the connector cover in the direction indicated by the arrow in the illustration and disconnect the connector cover.

    2. B002CBUC01
      *a Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.

    3. B002D59C01
      *a Holder
      B002C8N Remove in this Direction

      Disengage the holder as shown in the illustration.

    4. B002D2XC01
      B002C8N Remove in this Direction

      Remove the rear door outside handle assembly as shown in the illustration.

  36. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. B002EZDC01
      B002C8N Remove in this Direction

      Disengage the claws to remove the rear door front outside handle pad as shown in the illustration.

  37. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. B002DBFC01
      B002C8N Remove in this Direction

      Disengage the claws to remove the rear door rear outside handle pad as shown in the illustration.

  38. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B002DC8

      Using a clip remover, disengage the clamp to remove the rear door outside handle frame sub-assembly.

    2. B002F1KC01
      B002C8N Remove in this Direction

      Using a T30 "TORX" socket wrench, loosen the screw.

    3. Remove the rear door outside handle frame sub-assembly as shown in the illustration.

  39. REMOVE NO. 2 REAR DOOR WEATHERSTRIP


    1. B002CZP

      Using a clip remover, disengage the clips to remove the No. 2 rear door weatherstrip.

  40. REMOVE NO. 3 REAR DOOR WEATHERSTRIP


    1. B002E2AC01
      *a Double-sided Tape

      Remove the 2 double-sided tapes and No. 3 rear door weatherstrip.

      Note

      Remove any remaining double-side tape from the rear door panel sub-assembly.

  41. REMOVE REAR DOOR DUST PROOF SEAL


    1. B002DIT

      Disengage the claw to remove the rear door dustproof seal.

  42. REMOVE REAR DOOR PANEL CUSHION


    1. B002EBF

      Remove the rear door panel cushion.

  43. REMOVE REAR DOOR CHECK ASSEMBLY


    1. B002D5E

      Remove the bolt, 2 nuts and rear door check assembly.

  44. REMOVE REAR DOOR WEATHERSTRIP


    1. B002D8P

      Using a clip remover, disengage the clips to remove the rear door weatherstrip.

  45. REMOVE REAR DOOR FRONT BELT MOULDING END COVER

    Click here

  46. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

    Click here

  47. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

    Click here