BACK WINDOW GLASS REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the back window glass removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system

Click here

LKA/LDA system

Click here

Pre-crash safety system
Adaptive high beam system
Reset power trunk lid Power trunk lid system

Click here

PROCEDURE


  1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

    Click here

  2. REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

    Click here

  3. REMOVE AMPLIFIER ANTENNA ASSEMBLY

    Click here

  4. REMOVE NO. 2 AMPLIFIER ANTENNA ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

    Click here

  5. REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING LH

    Click here

  6. REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. REMOVE BACK WINDOW GLASS

    Note

    As the stopper, bracket and harness are not supplied individually, be careful not to damage them when installing the back window glass.

    B002F0TC02
    *A for 1-piece Type
    *B for 2-piece Type
    *1 No. 1 Back Window Glass Stopper
    *2 No. 2 Back Window Glass Stopper

    1. B002DGS

      Disconnect the connectors.

    2. B002D2QC01
      B002CL1 Protective Tape

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    3. B002CINC02
      *a Matchmark

      Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

      Tech Tips

      Matchmarks do not need to be placed if the glass is not going to be reused.

    4. B002DIDC02
      *1 Back Window Glass Stopper
      *a Piano Wire

      From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.

      Note


      • If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.

      • Make sure not to deform the upper brackets.

      • Make sure not to damage the wire harness.

    5. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    6. Cut through the adhesive by pulling the piano wire around the back window glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the back window glass.

    7. Using suction cups, remove the back window glass.

      Note

      If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.

  8. REMOVE BACK WINDOW GLASS DAM KIT


    1. When reusing the back window glass:


      1. B002D54C01
        *a Back Side

        Using a scraper, remove the back window glass dam kit from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the back window glass dam kit with new one.

  9. REMOVE BACK WINDOW OUTSIDE MOULDING


    1. When reusing the back window glass:


      1. B002CPSC01
        *a Back Side

        Using a scraper, remove the back window outside moulding from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the back window outside moulding with a new one.

  10. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)


    1. When reusing the back window glass:


      1. B002E3OC01
        *a Back Side

        Using a scraper, remove the 2 No. 1 back window glass stoppers from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the 1-piece type No. 1 back window glass stoppers with new 2-piece type No. 1 and No. 2 back window glass stoppers.

  11. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. When reusing the back window glass:


      1. B002E3OC01
        *a Back Side

        Using a scraper, remove the 2 No. 2 back window glass stoppers from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 2 back window glass stoppers with new ones.

  12. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. B002EWV

      Remove the 2 No. 1 back window glass stoppers.

      Note

      Be sure to replace the No. 1 back window glass stoppers with new ones.