Click here

POWER WINDOW REGULATOR MOTOR(for Rear Side) INSPECTION

Click here
Click here

PROCEDURE


  1. Click here

    INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Note:

    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.


    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

      Click here


    1. A01QCUSC05
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)
      *b Motor Gear
      B002DP3 Clockwise
      B002CU5 Counterclockwise

      Check that the motor gear rotates smoothly as follows.

      Table 1. OK:
      Measurement Condition Specified Condition

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 10 (UP1).

      3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP1), connect terminal 10 (UP1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates clockwise (UP)

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 7 (DWN1).

      3. After disconnecting the negative (-) lead of the battery from terminal 7 (DWN1), connect terminal 7 (DWN1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates counterclockwise (DOWN)

      If the result is not as specified, replace the power window regulator motor assembly LH.

  2. Click here

    INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Note:

    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.


    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

      Click here


    1. A01Q8M6C05
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)
      *b Motor Gear
      B002DP3 Clockwise
      B002CU5 Counterclockwise

      Check that the motor gear rotates smoothly as follows.

      Table 2. OK:
      Measurement Condition Specified Condition

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 10 (UP1).

      3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP1), connect terminal 10 (UP1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates counterclockwise (UP)

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 7 (DWN1).

      3. After disconnecting the negative (-) lead of the battery from terminal 7 (DWN1), connect terminal 7 (DWN1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates clockwise (DOWN)

      If the result is not as specified, replace the power window regulator motor assembly RH.