POWER WINDOW REGULATOR MOTOR(for Front Side) INSPECTION

PROCEDURE


  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Note


    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.


    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

      Click here


    1. A01QCUSC05
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)
      *b Motor Gear
      B002DP3 Clockwise
      B002CU5 Counterclockwise

      Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition Specified Condition

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 10 (UP1).

      3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP1), connect terminal 10 (UP1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates clockwise (UP)

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 7 (DWN1).

      3. After disconnecting the negative (-) lead of the battery from terminal 7 (DWN1), connect terminal 7 (DWN1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates counterclockwise (DOWN)

      If the result is not as specified, replace the power window regulator motor assembly LH.

  2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Note


    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.


    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

      Click here


    1. A01Q8M6C05
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)
      *b Motor Gear
      B002DP3 Clockwise
      B002CU5 Counterclockwise

      Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition Specified Condition

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 10 (UP1).

      3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP1), connect terminal 10 (UP1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates counterclockwise (UP)

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (E), and hold for 3 seconds or more.

      2. While terminals 2 (B) and 1 (E) are connected, connect the negative (-) lead of the battery to terminal 7 (DWN1).

      3. After disconnecting the negative (-) lead of the battery from terminal 7 (DWN1), connect terminal 7 (DWN1) to the negative (-) lead of the battery again within 1 second.

      		 Motor gear rotates clockwise (DOWN)

      If the result is not as specified, replace the power window regulator motor assembly RH.