FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT BELT RETRACTOR COVER


    1. B002E3I

      Engage the guide to install the front seat belt retractor cover.

  2. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. B002D8HE02

      Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

    2. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    1. B002CJPC01
      *a Unlock
      *b Lock
      *c 45°

      Before installing the front seat outer belt assembly, check the ELR function.


      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        Note

        Do not disassemble the retractor.

    2. B002D36E01

      Engage the guides to temporarily install the front seat outer belt assembly with the 2 bolts.

    3. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      Upper side
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Lower side
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. B002DJXC01
      *1 Locking Button

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    5. Connect the tension reducer connector.

    6. Connect the shoulder anchor of the front seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Connect the lower anchor of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    8. Inspect ELR lock.


      1. Check that when installed to the vehicle, pulling the belt out quickly will cause the belt to lock.

    9. Remove the bolt to disconnect the lower anchor of the front seat outer belt assembly.

  4. INSTALL CENTER UPPER PILLAR GARNISH

    Click here

  5. INSTALL CENTER LOWER PILLAR GARNISH

    Click here

  6. CONNECT FRONT SEAT OUTER BELT ASSEMBLY


    1. B002DX6C01
      *a Protruding Part

      Connect the lower anchor of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the lower anchor of the front seat outer belt assembly to overlap the protruding part of the front seat assembly.

  7. INSTALL SEAT BELT ANCHOR COVER CAP


    1. B002E8GC01
      B002C8N Install in this direction

      Engage the guides and claws to install the seat belt anchor cover cap as shown in the illustration.

  8. INSTALL REAR DOOR SCUFF PLATE

    Click here

  9. INSTALL FRONT DOOR SCUFF PLATE

    Click here

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  11. INSPECT SRS WARNING LIGHT

    Click here