KNEE AIRBAG ASSEMBLY(for Front Passenger Side) DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B002ENQ

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.

  2. DISPOSE OF LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (When Installed in Vehicle)

    Note


    • When disposing of the lower No. 2 instrument panel airbag assembly, use an unneeded vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B002E77N26

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B002CSN

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    4. Remove the No. 2 instrument panel under cover sub-assembly.

      Click here

    5. B002CIJC03
      *a Housing Lock
      *b CPA Upper Part
      B002CL1 CPA

      Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the airbag connector cannot be disconnected yet.)

      2. Push down the housing lock again and disconnect the airbag connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

    6. Install SST.


      1. B002E4VN01

        Connect the SST connector to the lower No. 2 instrument panel airbag assembly.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

        CAUTION:


        • B002E99

          Do not deploy if the lower No. 2 instrument panel airbag assembly is loose.

        • If deployed while the lower No. 2 instrument panel airbag assembly is loose, the lower No. 2 instrument panel airbag assembly may fly off and cause serious injuries.

      2. B002CJJC02
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

      3. While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

        CAUTION:


        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        B002CMV

        Note

        Take care not to damage the SST wire harness.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    7. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B002D7Q

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Remove the lower No. 2 instrument panel airbag assembly.

      Click here

      CAUTION:


      • B002EEB

        The lower No. 2 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B002DV2

        Do not apply water etc. to a lower No. 2 instrument panel airbag assembly with a deployed airbag.

      • If water is applied to the lower No. 2 instrument panel airbag assembly immediately after deployment, burns may occur from the resulting steam.

      • B002EPT

        Always wear protective glasses and gloves when handling a deployed lower No. 2 instrument panel airbag assembly.

      • If the lower No. 2 instrument panel airbag assembly is touched without wearing protective glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the lower No. 2 instrument panel airbag assembly in a plastic bag.

    9. Dispose of the lower No. 2 instrument panel airbag assembly.


      1. Place the lower No. 2 instrument panel airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B002E4T

          The lower No. 2 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B002D8X

          Do not apply water etc. to a lower No. 2 instrument panel airbag assembly with a deployed airbag.

        • If water is applied to the lower No. 2 instrument panel airbag assembly immediately after deployment, burns may occur from the resulting steam.

        • B002EEA

          Always wear protective glasses and gloves when handling a deployed lower No. 2 instrument panel airbag assembly.

        • If the lower No. 2 instrument panel airbag assembly is touched without wearing protective glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B002C8E

          Never dispose of a lower No. 2 instrument panel airbag assembly with an undeployed airbag.

        • If an undeployed lower No. 2 instrument panel airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        Note

        Always wash your hands with water after completing the operation.

  3. DISPOSE OF LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B002E77N26

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the lower No. 2 instrument panel airbag assembly.

      Click here

      CAUTION:

      B002DW2

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. B002EXBC28
      *a Wire Diameter
      *b Stripped Wire Section

      Using braided wire, tie down the lower No. 2 instrument panel airbag assembly to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the lower No. 2 instrument panel airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2/ 4


      1. Position the lower No. 2 instrument panel airbag assembly inside the tire with the airbag deployment side facing inside.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)
        B002EF6C01
        *a Inner Diameter *b Width

        Note

        The tires may be damaged by the airbag deployment, so use unneeded tires.

    4. Install SST.


      1. B002E8QN01

        After connecting the following SST to each other, connect them to the lower No. 2 instrument panel airbag assembly.

        SST
        09082-00802   ( 09082-10801, 09082-20801 )

    5. Place the tires.


      1. B002CZZC01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the lower No. 2 instrument panel airbag assembly is tied.

      2. Place at least 2 tires onto the tire to which the lower No. 2 instrument panel airbag assembly is tied. The top tire should have a wheel installed.

        Note


        • Do not place the SST connector under the tire because it could be damaged.

        • The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

      3. B002EUF

        Tie the tires together with the 2 wires.

    6. Install SST.


      1. B002D3TC01
        *a 10 m or more

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the lower No. 2 instrument panel airbag assembly is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B002CPR

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the lower No. 2 instrument panel airbag assembly.


      1. Remove the lower No. 2 instrument panel airbag assembly from the wheel.

        CAUTION:


        • B002E4T

          The lower No. 2 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B002D8X

          Do not apply water etc. to a lower No. 2 instrument panel airbag assembly with a deployed airbag.

        • If water is applied to the lower No. 2 instrument panel airbag assembly immediately after deployment, burns may occur from the resulting steam.

        • B002EEA

          Always wear protective glasses and gloves when handling a deployed lower No. 2 instrument panel airbag assembly.

        • If the lower No. 2 instrument panel airbag assembly is touched without wearing protective glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      2. Place the lower No. 2 instrument panel airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B002C8E

          Never dispose of a lower No. 2 instrument panel airbag assembly with an undeployed airbag.

        • If an undeployed lower No. 2 instrument panel airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        Note

        Always wash your hands with water after completing the operation.