SPIRAL CABLE INSTALLATION

PROCEDURE


  1. INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Check if the spiral cable with sensor sub-assembly is centered.

      B002CHRC02
      *A w/o Steering Heater *B w/ Steering Heater
      *1 Alignment Mark *2 Colored Roller (Yellow)
      *3 Flat Cable - -

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the alignment marks are aligned and the colored roller (yellow) or flat cable shown in the illustration is visible.

    2. If the spiral cable with sensor sub-assembly is not centered, center it.

      If the cable cannot be centered, it is possible that the spiral cable with sensor sub-assembly is broken. Replace the spiral cable with sensor sub-assembly with a new one.


      1. B002DB6C07
        B002EJY Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      2. B002C9Q

        Rotate the spiral cable with sensor sub-assembly approximately 2.5 rotations in the clockwise direction from the locked position until the colored roller (yellow) or flat cable can be seen, and then align the alignment marks.

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  2. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • B002DW2

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. Check that the front wheels are facing straight ahead.

    4. B002D7C

      Engage the claws to install the spiral cable with sensor sub-assembly.

      Note

      When replacing the spiral cable with sensor sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    5. Connect the connectors.

    6. B002EJCC04
      *a Slider

      Connect the airbag connector and check that the slider is in the lock position.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL STEERING COLUMN COVER

    Click here

  4. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  5. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • B002DW2

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. Check if the spiral cable with sensor sub-assembly is centered.

      B002CHRC02
      *A w/o Steering Heater *B w/ Steering Heater
      *1 Alignment Mark *2 Colored Roller (Yellow)
      *3 Flat Cable - -

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the alignment marks are aligned and the colored roller (yellow) or flat cable shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.

    5. B002EFTC01
      B002EJY Interlock

      While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

      Note


      • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

      • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

    6. B002ED0C01
      B002EJY Interlock

      While pushing on the interlock indicated, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored roller (yellow) or flat cable is visible.

      Note


      • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

      • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      Tech Tips

      The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  6. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  7. ENABLE AUTOAWAY/RETURN FUNCTION


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter.

      Click here