STEERING PAD DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B002ENQ

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.

  2. DISPOSE OF HORN BUTTON ASSEMBLY (When Installed in Vehicle)

    Note


    • When disposing of the horn button assembly, use an unneeded vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B002E77N26

      Check the function of SST.

      SST
      09082-00700

      CAUTION:


      • When deploying the airbag, always use the specified SST:

        SRS Airbag Deployment Tool

      • B002C8O

        If the procedure is performed using unspecified SST, the airbag may deploy in an unforeseen situation and cause a serious accident.


      1. B002DTCN03

        Connect SST to the battery.

        Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. B002DODN10

        Check the function of SST.

        Press the SST activation switch and check that the LED of the SST activation switch comes on.

        CAUTION:


        • Do not connect the SST connector to the airbag before inspecting SST.

        • If the airbag deploys due to malfunction of SST, it may cause a serious accident.

        • If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.

      3. Disconnect SST from the battery.

    2. Refer to Precaution.

      Click here

    3. Remove the lower steering column cover.

      Click here

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B002DW2

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Disconnect the airbag connector from the spiral cable with sensor sub-assembly.


      1. B002DYDC01
        *a Slider

        Slide the slider to release the lock, and then disconnect the connector.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    6. Install SST.


      1. B002EONE02

        Connect the SST connector to the airbag connector of the spiral with cable sensor sub-assembly.

        SST
        09082-00700

        CAUTION:


        • B002DSV

          Do not deploy if the steering wheel assembly and horn button assembly are loose.

        • If deployed while the steering wheel assembly and horn button assembly are loose, the steering wheel assembly and horn button assembly may fly off and cause serious injuries.

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      2. B002CJJC02
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

      3. While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

        CAUTION:


        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        B002CMV

        Note

        Take care not to damage the SST wire harness.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    7. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B002D7Q

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Remove the horn button assembly.

      Click here

      CAUTION:


      • B002DCN

        The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B002DJU

        Do not apply water etc. to a horn button assembly with a deployed airbag.

      • If water is applied to the horn button assembly immediately after deployment, burns may occur from the resulting steam.

      • B002E3E

        Always wear protective glasses and gloves when handling a deployed horn button assembly.

      • If the horn button assembly is touched without wearing protective glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the horn button assembly in a plastic bag.

    9. Dispose of the horn button assembly.


      1. Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B002CE6

          The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B002CWU

          Do not apply water etc. to a horn button assembly with a deployed airbag.

        • If water is applied to the horn button assembly immediately after deployment, burns may occur from the resulting steam.

        • B002EBO

          Always wear protective glasses and gloves when handling a deployed horn button assembly.

        • If the horn button assembly is touched without wearing protective glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B002CFD

          Never dispose of a horn button assembly with an undeployed airbag.

        • If an undeployed horn button assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        Note

        Always wash your hands with water after completing the operation.

  3. DISPOSE OF HORN BUTTON ASSEMBLY (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B002E77N26

      Check the function of SST.

      SST
      09082-00700

      CAUTION:


      • When deploying the airbag, always use the specified SST:

        SRS Airbag Deployment Tool

      • B002C8O

        If the procedure is performed using unspecified SST, the airbag may deploy in an unforeseen situation and cause a serious accident.


      1. B002DTCN02

        Connect SST to the battery.

        Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. B002DODN10

        Check the function of SST.

        Press the SST activation switch and check that the LED of the SST activation switch comes on.

        CAUTION:


        • Do not connect the SST connector to the airbag before inspecting SST.

        • If the airbag deploys due to malfunction of SST, it may cause a serious accident.

        • If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.

      3. Disconnect SST from the battery.

    2. Remove the horn button assembly.

      Click here

      CAUTION:

      B002DW2

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. B002EXBC28
      *a Wire Diameter
      *b Stripped Wire Section

      Using braided wire, tie down the horn button assembly to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the horn button assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2/ 4


      1. B002EK0E01

        After connecting the following SST to each other, connect them to the horn button assembly.

        SST
        09082-00802   ( 09082-10801, 09082-30801 )
      2. B002E6IC01
        *a 2 times or more

        Wind 3 wires at least 2 times each around each of the pins.

      3. B002CKNC01
        *a Deployment Side

        Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the horn button assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

        Note

        The tire and wheel may be damaged by the airbag deployment, so use an unneeded tire and wheel.

    4. B002EGEE01

      Install SST.


      1. Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the disc wheel.

      2. B002DSDC01
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the wheel.

    5. B002F0PC01
      *a Weight

      Cover the horn button assembly (using a cardboard box).


      1. Cover the horn button assembly with a cardboard box.

      2. Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

        Minimum cardboard box size
        Must exceed the following dimensions
        X
        460 mm (1.51 ft.)
        Y
        650 mm (2.13 ft.)

        Note


        • When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the horn button assembly is tied, X should be the following size.

          X = 460 mm (1.51 ft.) + width of tire

        • If a cardboard box smaller than the specified size is used, it may be broken by the shock from the airbag deployment.

    6. Cover the horn button assembly (using tires).


      1. B002EDIC01
        *a Inner Diameter
        *b Width
        *c Tires (3 or more)

        Place at least 3 tires without wheels onto the wheel and tire to which the horn button assembly is tied.

      2. Place a wheel and tire on top.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note


        • The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

        • Do not place the SST connector under the tire because it could be damaged.

      3. B002EUF

        Tie the tires together with the 2 wires.

    7. Deploy the airbag.


      1. B002DYOC01
        *A Using a Cardboard Box
        *B Using Tires
        *a 10 m or more

        Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B002DCF

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the horn button assembly.

      CAUTION:


      • B002CE6

        The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B002CWU

        Do not apply water etc. to a horn button assembly with a deployed airbag.

      • If water is applied to the horn button assembly immediately after deployment, burns may occur from the resulting steam.

      • B002EBO

        Always wear protective glasses and gloves when handling a deployed horn button assembly.

      • If the horn button assembly is touched without wearing protective glasses and gloves, hot parts may cause burns and dust may enter the eyes.


      1. Remove the horn button assembly from the wheel.

        CAUTION:


        • B002CFD

          Never dispose of a horn button assembly with an undeployed airbag.

        • If an undeployed horn button assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        Note

        Always wash your hands with water after completing the operation.

      2. Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.