METER / GAUGE SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus:


      1. for Combination Meter: Body Electrical / Combination Meter / Data List.

      2. for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.

      3. for Engine: Powertrain / Engine / Data List.

    7. Read the Data List according to the display on the GTS.


      1. Combination Meter


        Body Electrical > Combination Meter > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        ODO/TRIP Change SW ODO/TRIP switch OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        P-Seatbelt Buckle SW Front passenger seat belt buckle switch OFF or ON

        OFF: Front passenger seat belt fastened

        ON: Front passenger seat belt unfastened

        		 -
        Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
        Engine Rpm Engine speed Min.: 0 rpm, Max.:12750 rpm Almost the same as actual tachometer -
        Coolant Temperature Engine coolant temperature Min.: 0°C (0°F), Max.: 127.5°C(261.5°F) 75 to 100 °C (167 to 212 °F): After warming up engine -
        Washer Switch Washer fluid level warning switch OFF or ON

        OFF: Washer fluid level not low

        ON: Washer fluid level low

        		 -
        Oil Level SW Engine oil level sensor OFF or ON

        OFF: Oil level not low

        ON: Oil level low

        		 -
        Light Control Up Switch Light control rheostat up switch OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Light Control Down Switch Light control rheostat down switch OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        +B Voltage Value Battery voltage Min.: 0 V, Max.:25.5 V 11 to 14 V -
        Integrated value for Maintenance Maintenance required reminder value Min.: 0 miles, Max.:25500 miles Driving distance after performing maintenance required reminder reset procedure displayed If the value is 5000(miles) or more, perform the maintenance required reminder reset procedure after performing maintenance.*
        Fuel Input Fuel input Min.: 0 L, Max.:127.5 L

        Fuel receiver gauge indicates F: 64.8 L

        Fuel receiver gauge indicates 3/4: 46.8 L

        Fuel receiver gauge indicates 1/2: 35.1 L

        Fuel receiver gauge indicates 1/4: 20.6 L

        Fuel receiver gauge indicates E: 3.3 L

        		 Unit: Liter
        Ambient Temperature Outside temperature Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) Almost the same as actual outside temperature The temperature displayed on the multi-information display is -40 to 50 °C (-40 to 122 °F)
        Engine Oil Temperature Engine oil temperature Min.: 0°C (32°F),Max.: 255°C (491°F)

        Engine oil temperature receiver gauge indication:

        When the indicator is in the center of the gauge: 80 to 105 °C (176 to 221 °F)

        When the indicator is in the red zone: 140 °C (284 °F) or more

        		 -
        Multi Switch (Up) Steering pad switch(Up) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Down) Steering pad switch(Down) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Menu) Steering pad switch(Menu) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Enter) Steering pad switch(Enter) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Right) Steering pad switch(Right) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Multi Switch (Left) Steering pad switch(Left) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Oil Pressure Switch Oil pressure switch OFF or ON

        OFF: Engine started

        ON: Engine not started

        		 -
        Turn Signal Switch (Right) Oil pressure switch OFF or ON

        OFF: RH turn signal switch off

        ON: RH turn signal switch on

        		 -
        Turn Signal Switch (Left) LH turn signal switch OFF or ON

        OFF: LH turn signal switch off

        ON: LH turn signal switch on

        		 -
        Hazard Flasher Switch Hazard warning signal switch OFF or ON

        OFF: Hazard warning signal switch off

        ON: Hazard warning signal switch on

        		 -
        Passenger Occupant Detection Switch Occupant detection sensor OFF or ON

        OFF: Front passenger seat not occupied

        ON: Front passenger seat occupied

        		 -
        Multi Switch (Back) Steering pad switch(Back) OFF or ON

        OFF: Switch released

        ON: Switch pushed

        		 -
        Brake pad Sensor Signal Brake pad sensor signal OFF or ON

        OFF: Brake pad sensor signal not input

        ON: Brake pad sensor signal input

        		 -
        Engine Oil Temperature Sensor Signal Engine oil temperature sensor signal OFF or ON

        OFF: Engine oil temperature sensor signal not input

        ON: Engine oil temperature sensor signal input

        		 -
        Brake Fluid Amount Brake fluid level OK or NG

        OK: Brake fluid level normal

        NG: Brake fluid level abnormal

        		 -
        Driver Side Seatbelt Warning Buzzer Setting of the driver seatbelt warning buzzer OFF or ON

        OFF: Seatbelt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

        ON: Seatbelt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened

        		 Displays customize setting of Driver Side Seatbelt Warning Buzzer
        P-Seatbelt Warning Buzzer Setting of the front passenger seatbelt warning buzzer OFF or ON

        OFF: Seatbelt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when front passenger seatbelt unfastened

        ON: Seatbelt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when front passenger seatbelt unfastened

        		 Displays customize setting of Front Passenger Side Seatbelt Warning Buzzer
        ECO Drive Indicator Zone Setting of the ECO drive indicator zone OFF or ON

        OFF: Active

        ON: Non Active

        		 -
        ODO Display Time After IG OFF Setting Setting of the ODO display time after the engine switch is turned off 30s, 60s, 600s, OFF Displays customize setting of ODO display time after the engine switch is turned off -
        Flasher Sound Volume Adjustment Setting of the flasher sound volume adjustment Small, Medium, Large Displays customize setting of flasher sound volume adjustment -
        TPMS System Existence of function With or Without

        With: w/ Tire pressure warning system

        Without: w/o Tire pressure warning system

        		 -
        LDA System Existence of function With or Without

        With: w/ LKA/LDA system

        Without: w/o LKA/LDA system

        		 -
        PCS System Existence of function With or Without

        With: w/ Pre-crash safety system

        Without: w/o Pre-crash safety system

        		 -
        Radar Cruise System Existence of function With or Without

        With: w/ Dynamic radar cruise control system

        Without: w/o Dynamic radar cruise control system

        		 -
        Road Sign Assist System Existence of function With or Without

        With: w/ Road sign assist system

        Without: w/o Road sign assist system

        		 -
        Number of Trouble Code The number of the DTC currently stored Min.: 0, Max.: 255 0 -

        • *: w/ Canister Pump Module

      2. ABS/VSC/TRC


        Chassis > ABS/VSC/TRC > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

      3. Engine


        Powertrain > Engine > Data List
        Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
        Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 700 to 800 rpm: Idling with warm engine Idling (engine warmed up and A/C off): 763 rpm When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
        Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up engine -

        This is the engine coolant temperature.

        Tech Tips


        • After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

        • After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal.

        • If the value is -40°C (-40°F), or 135°C (275°F), the sensor circuit is open or shorted.

        • Check if the engine overheats when the value indicates 135°C (275°F).

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Perform the Active Test according the display on the GTS.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Speed Meter Operation Speedometer

      • OFF, 0, 40, 80, 120, 160, 200 mph*1

      • OFF, 0, 40, 80, 120, 160, 200, 240, 280 km/h*2

      There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)

      (1) for Gauge speedometer


        Reference mph (for Fuel Receiver Gauge Scale R to1/1 Type) mph*1:

      • 40 → 42.0 to 44.5

      • 80 → 83.1 to 87.1

      • 120 → 124.7 to 129.6

      • 160 → 166.2 to 171.9

      • 200 → 207.8 to 214.2


        Reference km/h (for Fuel Receiver Gauge Scale R to 1/1 Type) km/h*2:

      • 40 → 41.7 to 46.2

      • 80 → 83.4 to 88.4

      • 120 → 125.1 to 130.6

      • 160 → 166.2 to 173.2

      • 200 → 207.7 to 215.7

      • 240 → 249.2 to 258.0

      • 280 → 290.6 to 300.4


        Reference km/h (for Fuel Receiver Gauge Scale E to F Type) km/h*2:

      • 40 → 41.4 to 45.9

      • 80 → 82.8 to 87.8

      • 120 → 124.1 to 129.1

      • 160 → 165.5 to 170.5

      • 200 → 206.9 to 211.9

      • 240 → 248.3 to 253.3

      • 280 → 289.6 to 294.6

      (2) for Digital speedometer


        Reference mph*1:

      • 40 → 42.0 to 44.5

      • 80 → 83.1 to 87.1

      • 120 → 124.7 to 129.6

      • 160 → 166.2 to 171.9

      • 200 → 207.8 to 214.2


        Reference km/h*2:

      • 40 → 42.0 to 46.0

      • 80 → 84.0 to 88.0

      • 120 → 125.0 to 130.0

      • 160 → 167.0 to 173.0

      • 200 → 208.0 to 215.0

      • 240 → 249.0 to 257.0

      • 280 → 291.0 to 299.0
      A/T Indicator Operation 1 Shift indicator OFF, L, 2, 3(M), 4(M), D, N, R, P -
      A/T Indicator Operation 2 Shift indicator OFF, 8, 5, 6, 7, M -
      A/T Indicator Operation 3 Shift indicator OFF, D, SIL (Up), SIL (Down) -
      Indicat. Lamp Airbag SRS warning light OFF or ON -
      Indicat. Lamp Doors All Open Door open warning light OFF or ON -
      Driver Side Seat Belt Driver or front passenger seat belt warning light OFF or ON -
      Indicat. Lamp ABS ABS warning light OFF or ON -
      Indicat. Lamp Charge Charge warning light OFF or ON -
      Indicat. Lamp Slip Slip indicator light OFF or ON -
      Indicat. Lamp Beam High beam indicator light OFF or ON -
      Indicat. Lamp Head Head indicator light*1 OFF or ON -
      Indicat. Lamp Tail Tail indicator light*2 OFF or ON -
      Indicat. Lamp Rr FOG Rear fog indicator light*9 OFF or ON -
      Indicat. Lamp Fuel Fuel level warning light OFF or ON -
      VSC TRC Indicator TRC OFF indicator light OFF or ON -
      Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON -
      Indicat. Lamp ECB Brake warning light / yellow (minor malfunction) OFF or ON -
      Indicat. Lamp ECT SNOW SNOW indicator light*11 OFF or ON -
      Indicat. Lamp Cruise Cruise control indicator light*8 OFF or ON -
      Indicat. Lamp Brake Brake warning light OFF or ON -
      Indicat. EPS EPS warning light OFF or ON -
      Master Warning Master warning light OFF or ON -
      Indicat. Clearance Sonar LCD Clearance sonar indicator light*4 OFF or ON -
      Indicat. Park Parking brake warning light OFF or ON -
      Indicat. SET Cruise SET indicator light OFF or ON -
      Indicat. Radar Cruise Radar cruise control indicator light*5 OFF or ON -
      Indicat. VSC OFF VSC OFF indicator light OFF or ON -
      Automatic High Beam Indicator Automatic high beam indicator light*6 OFF or ON -
      Turn Signal (Left) Indicator LH turn indicator light OFF or ON -
      Turn Signal (Right) Indicator RH turn indicator light OFF or ON -
      Check Engine Indicator MIL (Check engine warning light) OFF or ON -
      BSM Control Indicator BSM indicator light*10 OFF or ON -
      Meter Display 1 Multi-information display OFF, All -

      • *1: for Speedometer with Imperial Units for Main Scale

      • *2: for Speedometer with Metric Units for Main Scale

      • *3: w/ Pre-crash Safety System

      • *4: w/ LEXUS Parking Assist-sensor System

      • *5: w/ Dynamic Radar Cruise Control System

      • *6: w/ Automatic High Beam System

      • *7: w/ LKA/LDA System

      • *8: w/o Dynamic Radar Cruise Control System

      • *9: w/ Rear Fog Light

      • *10: w/ Blind Spot Monitor System

      • *11: w/ Snow Mode Switch