THEFT DETERRENT SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Engine switch ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -
      IG SW Engine switch ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off or on (ACC)

      		 -
      RR Door Courtesy SW Rear door courtesy light switch assembly RH ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch assembly LH ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      		 -
      Trunk Lock/Unlock SW Door unlock switch sub-assembly*4 ON or OFF

      ON: Luggage compartment door lock key cylinder in unlock position

      OFF: Luggage compartment door lock key cylinder in neutral position

      		 Not applicable
      FR Door Lock Pos Front door RH unlock detection switch LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch assembly RH ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Lock Pos Front door LH unlock detection switch LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly LH ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      Hood Courtesy SW Engine hood courtesy switch ON or OFF

      ON: Engine hood open

      OFF: Engine hood closed

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      		 -
      RL-Door Lock Pos SW Rear door LH unlock detection switch ON or OFF

      ON: Rear door LH or RH unlocked

      OFF: Rear door LH and RH locked

      		 -
      Intrusion Sens OFF SW Intrusion sensor cancel switch*1*2 ON or OFF

      ON: Intrusion sensor cancel switch on

      OFF: Intrusion sensor cancel switch off

      		 -
      Glass Break Sensor Detection Glass break sensor detection*4 ON or OFF

      ON: Glass break sensor detection

      OFF: Glass break sensor not detection

      		 Not applicable
      Intrusion Sensor Detection status of the intrusion sensor (theft warning radar sensor)*1 ON or OFF

      ON: Intrusion detected

      OFF: Intrusion not detected

      		 -
      Tilt Sensor Detection status of the tilt sensor (yaw rate and acceleration sensor)*2 ON or OFF

      ON: Change in pitch angle detected

      OFF: Change in pitch angle not detected

      		 -
      Intrusion Sen Conn Intrusion sensor (theft warning radar sensor) connection*1 ON or OFF

      ON: Intrusion sensor connected

      OFF: Intrusion sensor not connected

      		 -
      Tilt Sensor Connect Tilt sensor (yaw rate and acceleration sensor) connection*2 ON or OFF

      ON: Tilt sensor (yaw rate and acceleration sensor) connected

      OFF: Tilt sensor (yaw rate and acceleration sensor) not connected

      		 -
      Intrusion Sensor Sound Detect Sound detection status of the intrusion sensor (theft warning radar sensor)*1*5 ON or OFF

      ON: Sound detected

      OFF: Sound not detected

      		 Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the GTS.
      Intrusion Win Opened Setting of the customized item "Intrusion Win Opened"*1 ON or OFF Customized value displayed -
      Security control with mechanism key Setting of the customized item "Security control with mechanism key"*3 ON or OFF Customized value displayed -
      Intrusion Sensor Sound Detection Function Setting of the customized item "Intrusion Sensor Sound Detection Function"*1 ON or OFF Customized value displayed -
      Intrusion Sensor Sensitivity Level Setting of the customized item "Intrusion Sensor Sensitivity Level"*1 Low or Normal Customized value displayed -
      Communication Theft Deterrent Connection status between theft deterrent ECU and main body ECU (multiplex network body ECU)*4 STOP or OK

      STOP: Communication stopped

      OK: Normal communication

      		 Not applicable
      The Number of DTC Number of DTCs 0 to 255 Number of DTCs will be displayed -

      • *1: w/ Intrusion Sensor Cancel Switch

      • *2: w/ Tilt Sensor

      • *3: Vehicles displaying the item "Security control with mechanism key" on the GTS

      • *4: Although the item is displayed on the GTS, it is not applicable to this vehicle.

      Note

      *5: Perform the intrusion sensor (theft warning radar sensor) operation inspection with the GTS disconnected.

      Click here

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Entry&Start / Active Test.

    5. According to the display on the GTS, perform the Active Test.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Security Horn2 Theft warning siren assembly*2 OFF/ON -
      Vehicle Horn Vehicle horns OFF/ON -
      Security Horn Security horn assembly*1 OFF/ON -
      Power For Intrusion Sensor Intrusion sensor (theft warning radar sensor) power supply*3 OFF/ON -
      Power For Tilt Sensor Tilt sensor (yaw rate and acceleration sensor) power supply*4 OFF/ON -

      • *1: w/ Security Horn Assembly

      • *2: w/o Security Horn Assembly

      • *3: w/ Intrusion Sensor Cancel Switch

      • *4: w/ Tilt Sensor


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Immobiliser Indicator Security indicator OFF/ON -