IMMOBILISER SYSTEM Security Indicator Light Does not Blink

DESCRIPTION

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door opened and closed with engine switch on (IG)).

WIRING DIAGRAM

A01QC3SE01

CAUTION / NOTICE / HINT

Note


  • The immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

    Click here

  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE


  1. CHECK FOR DTC


    1. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Powertrain > Engine > Trouble Codes
      OK
      DTCs are not output
      Result
      Proceed to
      OK
      NG

    NG

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    OK

  2. PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Immobiliser Indicator Security indicator light OFF/ON -

      Body Electrical > Entry&Start > Active Test
      Tester Display
      Immobiliser Indicator
      OK
      The security indicator light operates normally
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY))


    1. Disconnect the K74 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the K57*1 or r1*2 security indicator light (radio receiver assembly) connector.


      • *1: w/o Canister Pump Module

      • *2: w/ Canister Pump Module

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K74-18 (IND) - K57-37 (SEUC)*1 Always Below 1 Ω
      K74-18 (IND) or K57-37 (SEUC) - Body ground*1 Always 10 kΩ or higher
      K74-18 (IND) - r1-37 (SEUC)*2 Always Below 1 Ω
      K74-18 (IND) or r1-37 (SEUC) - Body ground*2 Always 10 kΩ or higher

      • *1: w/o Canister Pump Module

      • *2: w/ Canister Pump Module

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Reconnect the K74 certification ECU (smart key ECU assembly) connector.

    2. Reconnect the K57*1 or r1*2 security indicator light (radio receiver assembly) connector.


      • *1: w/o Canister Pump Module

      • *2: w/ Canister Pump Module

    3. Using an oscilloscope, check the waveform.

      B002DJZC94
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 - -
      Measurement Condition
      Tester Connection Switch Condition Specified Condition
      K74-18 (IND) - Body ground Engine switch off → on (IG) Pulse generation → Below 2 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SECURITY INDICATOR LIGHT (RADIO RECEIVER ASSEMBLY) Click here

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)