REAR DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

   
   

   1. Check the door lock motor operation.

      

      *a	Lock	*b	Unlock
      *c	Component without harness connected (Rear Door Lock Assembly LH)	-	-

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         If the result is not as specified, replace the rear door lock assembly LH.

   2. Check the door unlock detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (LSSR) - 9 (E) Unlock Below 1 Ω 6 (LSSR) - 9 (E) Lock 10 kΩ or higher

         If the result is not as specified, replace the rear door lock assembly LH.

2. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

   
   

   1. Check the door lock motor operation.

      

      *a	Lock	*b	Unlock
      *c	Component without harness connected (Rear Door Lock assembly LH)	-	-

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L) Unlock Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL) Set Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL) Unset

         If the result is not as specified, replace the rear door lock assembly LH.

   2. Check the door unlock detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (LSSR) - 5 (E) Unlock Below 1 Ω 6 (LSSR) - 5 (E) Lock 10 kΩ or higher

         If the result is not as specified, replace the rear door lock assembly LH.

3. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

   
   

   1. Check the door lock motor operation.

      

      *a	Unlock	*b	Lock
      *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         If the result is not as specified, replace the rear door lock assembly RH.

   2. Check the door unlock detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (LSSR) - 6 (E) Unlock Below 1 Ω 9 (LSSR) - 6 (E) Lock 10 kΩ or higher

         If the result is not as specified, replace the rear door lock assembly RH.

4. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

   
   

   1. Check the door lock motor operation.

      

      *a	Unlock	*b	Lock
      *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) Lock Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) Unlock Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL) Set Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL) Unset

         If the result is not as specified, replace the rear door lock assembly RH.

   2. Check the door unlock detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (LSSR) - 10 (E) Unlock Below 1 Ω 9 (LSSR) - 10 (E) Lock 10 kΩ or higher

         If the result is not as specified, replace the rear door lock assembly RH.