REAR DOOR LOCK INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RHD and LHD vehicles.

  • The procedure listed below is for the LHD vehicles.

  • Use the same procedures for both the LH and RH sides.

  • The procedure described below is for the LH side.

PROCEDURE


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B002EMOC01
      *A w/o Double Locking System
      *B w/ Double Locking System

      Engage the guide to install the rear door inside locking cable assembly.

    2. B002E7LC01
      *A w/o Double Locking System
      *B w/ Double Locking System
      B002C8N Install in this Direction

      Engage the claw to close the cover as shown in the illustration.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B002ET8C01
      *A w/o Double Locking System
      *B w/ Double Locking System

      Engage the guide to install the rear door lock remote control cable assembly.

    2. B002DQSC01
      *A w/o Double Locking System
      *B w/ Double Locking System
      B002C8N Install in this Direction

      Engage the claw to close the cover as shown in the illustration.

  3. INSTALL REAR DOOR LOCK ASSEMBLY

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to contact the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.


    1. Apply MP grease to the sliding parts of the rear door lock assembly.

    2. When reusing the rear door lock assembly:


      1. Install a new door lock wiring harness seal to the rear door lock assembly.

    3. B002ERKC01
      *1 Release Plate
      B002C8N Install in this Direction

      Connect the release plate as shown in the illustration.

      Tech Tips

      Make sure that the release plate is securely connected to the rear door lock assembly.

    4. Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    5. Connect the connector.

  4. INSTALL REAR DOOR GLASS RUN

    Click here

  5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  6. INSTALL REAR DOOR QUARTER WINDOW GLASS

    Click here

  7. INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

    Click here

  8. INSTALL REAR DOOR SERVICE HOLE COVER

    Click here

  9. INSTALL REAR NO. 2 SPEAKER ASSEMBLY

    Click here

  10. INSTALL REAR DOOR ARMREST SET BRACKET

    Click here

  11. INSTALL REAR DOOR FRAME GARNISH

    Click here

  12. INSTALL REAR SIDE CURTAIN ASSEMBLY (w/ Rear Sunshade)

    Click here

  13. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

    Click here

  14. INSTALL REAR DOOR TRIM COVER

    Click here

  15. INSTALL NO. 1 REAR DOOR STIFFENER CUSHION

    Click here

  16. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  17. INSTALL REAR ARMREST BASE UPPER PANEL SUB-ASSEMBLY

    Click here

  18. INSTALL REAR DOOR HOLE COVER

    Click here

  19. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here