ENTRY AND START SYSTEM(for Start Function), Diagnostic DTC:B2285

DTC Code DTC Name
B2285 Steering Lock Position Signal Circuit Malfunction

DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upr bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

Tech Tips

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2285 Steering Lock Position Signal Circuit Malfunction The steering lock position signal sent by the steering lock ECU (steering lock actuator or upr bracket assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.

  • AM2 fuse

  • Steering lock ECU (steering lock actuator or upr bracket assembly)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

 Disconnect the cable from the negative(-) battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) battery terminal. Wait 40 seconds or more with the engine switch off (with the steering wheel locked), then turn the engine switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine cannot be started. The ECU does not send an engine start request.
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2285

    Power Source Control:

  • Steering Unlock Switch


    Entry&Start:

  • Power Supply Short

  • Motor Driver Short

  • Lock Bar Stuck Error

 -

WIRING DIAGRAM

B002DKKE01

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upr bracket assembly), refer to the entry and start system (for Start Function) precaution.

    Click here

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

PROCEDURE


  1. CHECK FOR DTC (LIN COMMUNICATION SYSTEM)


    1. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes

      Tech Tips


      • If the steering wheel cannot be locked or unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.

      • If LIN communication is not available, the steering wheel cannot be locked or unlocked.

      OK
      LIN communication system DTC B2785 is not output simultaneously.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO DTC B2785 Click here

    OK

  2. READ VALUE USING GTS (STEERING UNLOCK SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. According to the display on the GTS, read the Data List.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF

      ON: Steering unlocked

      OFF: Steering locked

      • When the shift lever is in P and the engine switch is off, if any door is opened or closed, the steering is locked.

      • When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

      • The engine cannot be started when the steering unlock signal is off.

      Body Electrical > Power Source Control > Data List
      Tester Display
      Steering Unlock Switch
      Result
      Result Proceed to
      Data List item does not change A
      Data List item changes B

    B

    REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    1. B002EYSC72
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A21-2 (+B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

    OK

  4. CHECK HARNESS AND CONNECTOR (GROUND)


    1. B002EYSC73
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A21-11 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY)


    1. B002D0HC01
      *a

      Component with harness connected

      (Steering Lock ECU (Steering Lock Actuator or Upr Bracket Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Positive (+) tester probe → K20-4 (SLP1) Negative (-) tester probe → Body ground Steering locked* 10 kΩ or higher
      Steering unlocked* Below 1 Ω

      Tech Tips


      • *: If any of the doors are opened then closed with the shift lever in P and the engine switch off, the steering wheel will be locked. If the engine switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.

      • DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator or upr bracket assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator or upr bracket assembly) to the certification ECU (smart key ECU assembly) individually.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY) Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY))


    1. Disconnect the K74 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the K20 steering lock ECU (steering lock actuator or upr bracket assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K74-26 (SLP) - K20-4 (SLP1) Always Below 1 Ω
      K74-26 (SLP) or K20-4 (SLP1) - Body ground 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR