FAIL-SAFE FUNCTION
When communication fails in any of the CAN bus wires (communication wires), a fail-safe function(s) operates. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.
Effects on each system when communication is impossible (for further details, see the pages for each system).
| Function |
|
Behavior during CAN Failure | ||
|---|---|---|---|---|
| Vehicle Behavior | Indicator and Buzzer | Diagnostic Trouble Code | ||
| Lost Communication Detection (The frames of the ECU connected to the global bus are monitored to detect for ECU communication failures.) |
|
The communication failure time is recorded. | Nothing | - |
| Air Conditioner
|
|
|
Nothing | U0100 (Air conditioning amplifier assembly) |
| Compressor Control (Determines whether the compressor is locked using engine speed information.) |
|
While the engine switch is on (IG), control is performed with the default engine speed value (0 rpm). | Nothing | U0100 (Air conditioning amplifier assembly) |
| Simple Load Control (Limits electrical load control according to the load control level.) |
|
While the engine switch is on (IG), the current state is maintained (during a reset, there is no load control). | Nothing | U0131 (Air conditioning amplifier assembly) |
| Panel Control
|
|
While the engine switch is on (IG), the switch is off and the exhaust gas availability information is maintained. | Cannot change the operation state of the air conditioning system when the engine switch is on (IG). | U0163 (Air conditioning amplifier assembly) |
| Panel Dimming Control (Outputs dimming information to the LIN panel according to the display dimming information.) |
|
While the engine switch is on (IG), the current state is maintained (during a reset, dimming control is performed). | Cannot switch between dimming states (after a reset is performed, the system stays in dimming mode). | U0142 (Air conditioning amplifier assembly) |
| Destination Determination Control (Switches the A/C control pattern according to the destination information.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | U0142 (Air conditioning amplifier assembly) |
| Remote Start Control (Controls the air conditioning operation state according to remote start information.) |
|
While the engine switch is on (IG), remote start control is not performed. | While the engine switch is on (IG), the A/C system does not begin operation according to the remote start information. | - |
| Outside Temperature Compensation Control (Changes the air conditioning system operation state and adjusts the outside temperature display value according to the vehicle speed.) |
|
While the engine switch is on (IG), control is performed with the default vehicle speed value (0 km/h [0 mph]). |
|
U0155 (Air conditioning amplifier assembly) |
| Air Conditioning ECO Control (ECO-mode control is performed.) |
|
While the engine switch is on (IG), the previous value is maintained (after a reset, the system stays in its normal state of operation). | Nothing | - |
| Engine System Indicator Display
|
|
|
|
- |
| Electrical Load Control (Idle up according to the electrical load is performed.) |
|
Idle up according to the electrical load is not performed. | The idling speed changes. | - |
| Air Conditioning Coordinated Control
|
|
Air conditioning coordinated control does not operate (cannot perform idle up). | Air conditioning does not operate. | - |
| PTC Heater (Performs idle up according to requests from the PTC heater [including coolant heater] or heater system.) |
|
The PTC heater does not operate. |
|
- |
| Charging Control (Performs idle up according to charging requests.) |
|
|
|
- |
| Eco Driving Indicator (Displays information to the driver to encourage Eco-driving.) |
|
Nothing | No information is displayed. | - |
| Integrated Control (VDM) (Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that driveability, acceleration performance and acceleration feeling are improved.) |
|
Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. | Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. | - |
| Eco Control (Performs electronic throttle control according to fuel consumption.) |
|
Nothing | Nothing | - |
| ECT System Indicator Display (Indicates the shift position, states of switches, system modes, etc.) |
|
Nothing | Nothing | - |
| AI-SHIFT Control (Controls the automatic transmission in order to improve engine braking power and acceleration feel.) |
|
AI-SHIFT control does not operate. | Nothing | - |
| Neutral Control (Reduces engine load and performs idle up.) |
|
Neutral control is not performed. | Nothing | - |
| Coast Downshift/Heater Requested Upshift Delay (Changes the coast downshift point based on the air conditioning load. Performs heater requested upshift delay.) |
|
Coast downshift does not operate. | Coast downshift shock becomes stronger. | - |
| Cruise Control (Adjusts engine throttle valve opening amount automatically to maintain vehicle speed) |
|
Nothing |
|
- |
| Cruise control does not operate. | Cruise control does not operate. | U0122 (Driving support ECU assembly) |
||
| Electronic Power Steering System (Calculates the current to be used for the steering assist according to the torque sensor value and vehicle speed, and then operates the motor.) |
|
|
The EPS warning light illuminates. |
(Power steering ECU assembly) |
| VDIMα System (Calculates the current to be used for the steering assist according to the commanded value from VSC [Electronically Controlled Brake System], and then operates the motor.) |
|
VDIMα control is stopped. | Nothing | U0129 (Power steering ECU assembly) |
| Lane Keeping Assist System (Calculates the current to be used for the steering assist according to the commanded torque value from the FCM, and then operates the motor.) |
|
Lane keeping assist control ends. | Nothing | U1104 (Power steering ECU assembly) |
| Simple Load Control (Determines the current power supply and load status, and sends commands to limit control.) |
|
Nothing | Nothing | - |
| αB Control (Performs assist to prevent sliding sideways.) |
|
During αB control, if the data becomes invalid, control stops. | The EPS warning light illuminates. | U0129 (Power steering ECU assembly) |
| Steering Assist Calculation (Changes the assist force according to the vehicle speed.) |
|
|
The EPS warning light illuminates. | U0129 (Power steering ECU assembly) |
| DTC Output (When the TC signal is on, DTC information is sent according to the polling from MET.) |
|
Nothing | Nothing | - |
| Assist Map Selection (Selects the assist map according to the destination information, drivetrain [2WD or 4WD], engine type, etc.) |
|
|
There is no indication of a communication problem. However, the EPS warning light illuminates because an assist map is not selected. |
- |
| Idle Up (When a large assist current is created, a request to perform idle up is sent to the ECM in order to prevent the battery voltage from dropping.) |
|
Nothing | Nothing | - |
| Steering Center Point Learning (Learns the steering wheel center point.) |
|
The steering wheel center point is not learned if there is a problem with CAN communication. | The EPS warning light illuminates. | U0129 (Power steering ECU assembly) |
| Compensation Control (Performs assist according to the vehicle speed for various compensation controls.) |
|
When there is a problem with CAN communication (vehicle speed signal), the various controls operate with a set vehicle speed of 100 km/h (62 mph). | The EPS warning light illuminates. | U0129 (Power steering ECU assembly) |
| Vehicle Speed Display
|
|
Signal is considered to be 0. |
|
U0129 (Combination meter assembly) |
| Tachometer (Displays information on the tachometer.) |
|
|
|
U0100 (Combination meter assembly) |
| ECO Drive Indicator (Controls ECO display.) |
|
ECO display is not displayed. | ECO display is not displayed. | U0129 (Combination meter assembly) |
| ECO Display (Turns the ECO light on and off.) |
|
Signal is considered to be 0. | Turns the ECO light off. | U0100 (Combination meter assembly) |
| ECT/ENG System Display
|
|
Signal is considered to be 0. | The needle of the engine coolant temperature gauge is at the C mark or below. | - |
| Fuel Gauge
|
|
Signal is considered to be 0. | Calculation continues using a provisional value. |
(Combination meter assembly) |
| Odometer and trip meter display (Displays the driving distance.) |
|
Signal is considered to be 0. | The last displayed value remains. | U0129 (Combination meter assembly) |
| Shift Display (Displays the shift position.) |
|
Signal is considered to be 0. | Not displayed | - |
| Airbag (Turns the SRS warning light on and off.) |
|
Signal is considered to be "Active". | The airbag warning light illuminates. | U0151 (Combination meter assembly) |
| Seat Belt Warning
|
|
Signal is considered to be 0. | The seat belt warning light turns off. |
(Combination meter assembly) |
| ABS Warning (Turns the ABS warning light on and off.) |
|
Signal is considered to be "Active". | The ABS warning light illuminates. | U0129 (Combination meter assembly) |
| Brake Warning
|
|
|
The brake warning light illuminates. | U0129 (Combination meter assembly) |
| Brake Override System (Turns the brake override system light on and off.) |
|
Signal is considered to be "Active". | The brake override system light illuminates. | - |
| SLIP Warning (Turns the SLIP warning light on and off.) |
|
|
The SLIP indicator illuminates. | U0129 (Combination meter assembly) |
| TRC OFF (Turns the TRC OFF light on and off.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | U0129 (Combination meter assembly) |
| AT Fluid Temperature Warning (Illuminates / turns off AT fluid temperature warning light) |
|
|
Nothing | U0100 (Combination meter assembly) |
| Electronic Power Steering Warning (Turns the electronic power steering warning buzzer on and off.) |
|
Signal is considered to be "Active". | The electronic power steering warning light illuminates. | U0131 (Combination meter assembly) |
| Headlight System (Turns operation and warning lights on/off.) |
|
|
Nothing | U0182 (Combination meter assembly) |
| Light Reminder (Turns the warning buzzer on and off.) |
|
Signal is considered to be 0. | Nothing | - |
| Entry and Start Function
|
|
While the engine switch is on (IG), the current state is maintained. While the engine switch is OFF, the signal is considered to be "0" | Nothing | - |
| Intrusion Sensor (Displays the operation status.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Ajar Warning
|
|
|
Nothing | U0129 (Combination meter assembly) |
| Window/Roof Open Warning
|
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Destination (Determines the destination, etc.) |
|
The last signal state is maintained. | Nothing | U0142 (Combination meter assembly) |
| MIL
|
|
|
The MIL illuminates. | U0100 (Combination meter assembly) |
| Oil Pressure
|
|
|
Nothing |
(Combination meter assembly) |
| Oil Level
|
|
Signal is considered to be 0. | Nothing |
(Combination meter assembly) |
| Oil Maintenance (Turns the operation and warning display on and off.) |
|
Starter signal is controlled as "OFF". | Nothing | - |
| Injector Maintenance (Turns the operation and warning display on and off.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Battery Warning (Turns the battery light on and off.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Electrical Component Operation Limit (Turns the warning display on and off.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| TPMS (Warning Light) (Turns the tire pressure warning light on and off.) |
|
Signal is considered to be "Active". | The TPMS warning light illuminates. | U0142 (Combination meter assembly) |
| TPMS (Multi-display) (Displays the pressure in the multi-display.) |
|
|
The pressure valve display turns off. | U0142 (Combination meter assembly) |
| Cruise Control (Turns the cruise control/radar cruise control operation and warning display on and off.) |
|
|
Multi-information display does not show superimposed display. | - |
| Pre-crash Safety System (Turns the pre-crash safety light on and off.) |
|
|
The pre-crash safety indicator flashes. |
(Combination meter assembly) |
| Lane Departure Alert System (Turns the lane departure alert light on and off.) |
|
Signal is considered to be "Active". | The lane departure alert light illuminates. | U023A (Combination meter assembly) |
| Blind Spot Monitor System (Turns the blind spot monitor indicator on and off.) |
|
|
Nothing | - |
| Clearance Sonar
|
|
Signal is considered to be 0. |
|
- |
| Multi-media-linked (Navigation, audio, telephone, etc.) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | U0163 (Combination meter assembly) |
| Light on/off timing chart (Light illuminating/turning off timing) |
|
|
Nothing | - |
| WAKE UP/SLEEP (Toggles between "Normal Operating Mode (wakeup)" and "Sleep Mode") |
|
|
Nothing | - |
| Dimmer Control
|
|
|
Signal is considered to be 0. | - |
| Rental Car Mode Display (Displays odometer (ODO) distance when engine switch is turned off) |
|
Signal is considered to be 0. | Nothing | - |
| Rev Indicator
|
|
|
|
- |
| A/T Reverse Buzzer (Sounds / stops A/T Reverse Buzzer) |
|
|
Does not sound | - |
| Smart Key Intermittent Buzzer (Sounds / stops Smart Key Intermittent Buzzer) |
|
Does not sound | Does not sound | - |
| Smart Key Intermittent Buzzer (No. 2) (Sounds / stops Smart Key Intermittent Buzzer (No. 2)) |
|
The last signal state is maintained | Nothing | - |
| Smart Key Single Buzzer (Sounds / stops Smart Key Single Buzzer) |
|
The last signal state is maintained | Nothing | - |
| Immobiliser Key Certification Complete Notification (Sounds / stops Immobiliser Key Certification Complete Notification) |
|
The last signal state is maintained | Nothing | - |
| Radar Cruise Deceleration Cancel Buzzer (Sounds / stops Radar Cruise Deceleration Cancel Buzzer) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Sports Shift Reject Buzzer (Sounds / stops Sports Shift Reject Buzzer) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Door Opened When Not in P Range Warning Buzzer (Sounds / stops Door Opened When Not in P Range Warning Buzzer) |
|
Signal is considered to be 0. | Does not sound | - |
| LKA/LDA Buzzer (Sounds / stops LKA/LDA buzzer) |
|
|
Does not sound | - |
| BEAM Indicator (Illuminates / turns off BEAM Indicator) |
|
While the engine switch is on (IG), the current state is maintained. While the engine switch is OFF, the signal is considered to be "0". | Nothing | - |
| HEAD Indicator (Illuminates / turns off HEAD Indicator) |
|
While the engine switch is on (IG), the current state is maintained. While the engine switch is OFF, the signal is considered to be "0". | Nothing | - |
| TAIL Indicator (Illuminates / turns off TAIL Indicator) |
|
While the engine switch is on (IG), the current state is maintained. While the engine switch is OFF, the signal is considered to be "0". | Nothing | - |
| RrFOG Indicator (Illuminates / turns off RrFOG Indicator) |
|
While the engine switch is on (IG), the current state is maintained. While the engine switch is OFF, the signal is considered to be "0". | Nothing | - |
| SNOW MODE Indicator (Illuminates / turns off SNOW MODE Indicator) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Meter Multi-display (Controls state transitions, display contents and display method of the Meter Multi-display) |
|
Signal is considered to be 0. | Nothing | U0129 (Combination meter assembly) |
| GSI (Gear Shift Indicator) (Illuminates / turns off the GSI (Gear Shift Indicator)) |
|
Signal is considered to be 0. | Turns off | - |
| CIRCUIT MODE Indicator (Illuminates / turns off CIRCUIT MODE Indicator) |
|
Turns off | Turns off | - |
| Expert Indicator (Illuminates / turns off Expert Indicator) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Speed Warning Function (Displays / hides Middle East 120 km/h Speed Warning) |
|
Signal is considered to be 0. | Nothing | U0129 (Combination meter assembly) |
| TVD Warning Display (Displays / hides TVD Warning) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| Automatic 2nd_Lo Rejection on Low-friction Road Surface (Displays / turns off display of Automatic 2nd_Lo Rejection on Low-friction Road Surface) |
|
While the engine switch is on (IG), the current state is maintained. While the engine switch is OFF, the signal is considered to be "0". | Nothing | - |
| Door Lock / Unlock Mode Switch (Switches between Door Lock / Unlock Modes) |
|
|
Not Displayed | - |
| TVD Monitor (Displays TVD Status) |
|
|
|
U0129 (Combination meter assembly) |
| G Monitor (Displays G Monitor, Steering Angle, Brake Fluid Pressure and Accelerator Opening Angle status) |
|
|
|
U0129 (Combination meter assembly) |
| Estimated Fuel Consumption Display (Displays value calculated from fuel injection volume) |
|
Blank Display (Units are displayed). | Blank Display (Units are displayed). | - |
| Drive Monitor (Instantaneous Fuel Consumption) (Displays Instantaneous Fuel Consumption) |
|
|
Blank Display (Stops calculation of instantaneous fuel consumption). |
(Combination meter assembly) |
| Drive Monitor (Fuel Consumption Since Resetting) (Displays Instantaneous Fuel Consumption) |
|
|
Blank Display (Stops calculation of fuel consumption since resetting). |
(Combination meter assembly) |
| Drive Monitor (Average Fuel Consumption After Engine Start) (Displays Average Fuel Consumption After Engine Start-up) |
|
Blank Display (Stops calculation of Average Fuel Consumption After Engine Start). | Blank Display (Stops calculation of Average Fuel Consumption After Engine Start). |
(Combination meter assembly) |
| Drive Monitor (Average Fuel Consumption Since Last Refueling) (Displays Average Fuel Consumption Since Last Refueling) |
|
|
Blank Display (Stops calculation of Average Fuel Consumption Since Last Refueling). |
(Combination meter assembly) |
| Drive Monitor (Average Vehicle Speed Since Engine Start) (Displays Average Vehicle Speed Since Engine Start) |
|
|
Blank Display (Stops calculation of Average Vehicle Speed Since Engine Start). |
(Combination meter assembly) |
| Drive Monitor (Average Vehicle Speed Since Resetting) (Displays Average Vehicle Speed Since Resetting) |
|
|
Blank Display (Stops calculation of Average Vehicle Speed Since Resetting). |
(Combination meter assembly) |
| Possible Travel Distance (Displays Possible Travel Distance using engine type determination) |
|
|
Blank Display (Stops calculation of Possible Travel Distance). |
(Combination meter assembly) |
| Drive Monitor (Driving Time Since Engine Start) (Displays Driving Time Since Engine Start) |
|
|
Blank Display (Stops calculation of Possible Travel Distance). | U0100 (Combination meter assembly) |
| Drive Monitor (Driving Distance Since Engine Start) (Displays Driving Distance Since Engine Start) |
|
Blank Display (Stops calculation of Driving Distance Since Engine Start). | Blank Display (Stops calculation of Driving Distance Since Engine Start). |
(Combination meter assembly) |
| Drive Monitor (A/T Actual Gear Position) (Displays the A/T Actual Gear Position) |
|
|
Blank Display (Only title is displayed). | - |
| Ambient Temperature (Displays Ambient Temperature) |
|
Error Display | Error Display | - |
| Low Temperature Warning (Displays Low Temperature Warning) |
|
Freezing Display Flag = Not Set | Error Display | - |
| Turn / Hazard Light Output (Illuminates, blinks, and turns off the Turn / Hazard Lights) |
|
Signal is considered to be 0. | Nothing | - |
| Switch Operation Count History (Counts the number of operations of each type of hard switch, records switch operation count history and outputs DTCs.) |
|
|
Nothing | U0129 (Combination meter assembly) |
| DTC Display (Blinks and displays DTCs) |
|
|
|
(Combination meter assembly) |
| TSR Buzzer (Sounds / stops TSR Buzzer) |
|
The last signal state is maintained. | Nothing | - |
| ASL (Vehicle Speed Limit) Buzzer (Sounds / stops ASL (Vehicle Speed Limit) buzzer) |
|
Signal is considered to be 0. | Nothing | U0129 (Combination meter assembly) |
| Low Speed Range Vehicle Ahead Lost Buzzer (Sounds / stops Low Speed Range Vehicle Ahead Lost Buzzer) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| CHARGE (Telltale) (Illuminates / turns off CHARGE Warning light) |
|
Signal is considered to be 0. | Nothing | - |
| AVS / Drive Select Mode (Switches display between NORMAL, SPORT, S/S+, Eco) |
|
|
Nothing | - |
| Drift Warning (Performs Drift Warning Display) |
|
Signal is considered to be "Active". | Nothing | - |
| CDY Mode Display (Performs CDY Mode Display) |
|
While the engine switch is on (IG), the current state is maintained. | Nothing | - |
| TSR (Performs TSR Display) |
|
Signal is considered to be 0. | Nothing | - |
| Setting (Performs Setting Display and Configuration) |
|
Signal is considered to be 0. | Nothing | U0129 (Combination meter assembly) |
| HUD Navigation Linked (Performs mediation of interrupt display on/off to prevent navigation contents of the same granularity from being displayed redundantly on both the Meter and HUD) |
|
|
Nothing | - |
| Steering Angle Sensor (Detects the vehicle steering angle.) |
|
The steering angle sensor information signal is sent at regular intervals every 0.12 seconds. | Nothing | - |
| Trigger Response/Autonomous Transmission (Outputs the yaw rate and acceleration sensor signal.) |
|
The yaw rate sensor information signal is sent at regular intervals every 0.012 seconds. | Nothing | - |
| Trigger Response / Independent Transmission (Roll rate and vertical acceleration sensor signal output) |
|
The roll rate and vertical acceleration sensor information signal is sent at regular intervals every 0.012 seconds. | Nothing | - |
| Anti-lock Brake System Control (Prevents the wheels from locking during sudden stops.) |
|
|
|
(Brake actuator assembly (skid control ECU)) |
| Vehicle Stability Control/Traction Control (Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when accelerating from rest.) |
|
|
|
(Brake actuator assembly (skid control ECU)) |
| Hill-start Assist Control 3 (Maintains the brake oil pressure for 2 seconds when the brake pedal is depressed further.) |
|
|
|
(Brake actuator assembly (skid control ECU)) |
| Static Braking (When the vehicle is stopped, the parking brake electronically operates to hold the vehicle in place when the driver operates the switch.) |
|
It cannot be determined whether the vehicle is stopped or not (there is no effect on this function). | The electric parking brake warning light illuminates. |
(Parking brake ECU assembly) |
| Dynamic Parking Brake (Slows down the moving vehicle with the parking brake. Braking power is only effective while pressing the switch. Once the switch is released, the parking brake is automatically released.) |
|
It cannot be determined whether the vehicle is stopped or not (there is no effect on this function). | The electric parking brake warning light illuminates. |
(Parking brake ECU assembly) |
| Shift-linked Function (When the shift lever is moved to P, the electric parking brake automatically operates. If the shift lever is moved to D, N or R, the electric parking brake is automatically released.) |
|
The shift-linked function is prohibited. |
|
(Parking brake ECU assembly) |
| Brake Hold Function (Prevents the vehicle from moving when the brake pedal is released while the vehicle is stopped. Automatically operates the electric parking brake according to requests from the skid control ECU.) |
|
Brake hold control is prohibited. |
|
(Parking brake ECU assembly) |
| Air Conditioning Control (Controls the selecting of the registers, temperature adjustment, etc. according to remote touch operation.) |
|
|
Displays messages on the multi-information display. |
(Radio receiver assembly) |
| Clearance Sonar Settings/Notification (Controls the settings for the clearance sonar screen notifications which are set by remote touch operation, displays the sonar status and plays voice warnings.) |
|
|
|
(Radio receiver assembly) |
| Eco Navigation Display (Displays the fuel consumption in 1 minute intervals, and displays the average fuel consumption history.) |
|
|
|
(Radio receiver assembly) |
| Rear View Monitor Control (Displays the guide lines based on the steering sensor, vehicle speed and vehicle information [whether the vehicle is 2WD or 4WD, the VGRS information, ARS information and long/short information].) |
|
|
|
(Radio receiver assembly) |
| Destination Determination (Determines the destination based on the destination symbol and destination package information and selects the display language, time zone, etc.) |
|
Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value). | The time zone and language selection screens do not match the destination. | U0140 (Radio receiver assembly) |
| Vehicle Customize Function (Changes the behavior and control parameters of various functions (illumination lighting time, etc.) according to the user operation via the screen.) |
|
|
The customize options for items related to the ACN, BDB, IDT, DST and TAT ECU are not displayed or the settings cannot be saved. |
(Radio receiver assembly) |
| HUD Display Function (Displays the navigation intersection guide information on the meter or HUD device.) |
|
Nothing | Nothing | U0073 (Radio receiver assembly) |
| Meter-linked Function (Changes display based on customization information set through the meter. Outputs the customization information set in the system.) |
|
Maintains the last valid state. | Nothing | - |
| Information Sound Adjustment Function (Receives flags from the driving support ECU to operate the alarm, and limits or mutes multimedia audio while the alarm is in operation.) |
|
Audio mute is canceled. | Nothing | - |
| Entry and Start Function
|
|
An entry unlock retry is performed. |
|
(Certification ECU [smartkey ECU assembly]) |
| Entry and Start Function
|
|
The previous value is maintained. |
|
U0100 (Certification ECU [smartkey ECU assembly]) |
| Wireless Function (Operates the wireless lock/unlock functions, etc.) |
|
Nothing | When transmission is abnormal: Wireless lock/unlock and trunk functions do not operate. | - |
| Remote Engine Start Function (Requests for the immobiliser to be unset in response to data from the remote engine start ECU.) |
|
Nothing | The remote engine start does not operate. | U0142 (Certification ECU [smartkey ECU assembly]) |
| Memory Function (Moves the seat and steering wheel to the recorded positions when a smart entry unlock or wireless unlock operation is performed.) |
|
Nothing |
|
U0142 (Certification ECU [smartkey ECU assembly]) |
| Engine Switch Illumination Control (Operates the engine switch illumination in conjunction with the dome light illumination, etc.) |
|
|
|
U0142 (Certification ECU [smartkey ECU assembly]) |
| Door Lock (Operates the lock and unlock functions [the key-linked function, key lock-in prevention function, automatic lock function, etc.].) |
|
|
Nothing |
(Main body ECU (multiplex network body ECU)) |
| Alarm (Sounds various warnings.) |
|
Nothing | Nothing |
(Main body ECU (multiplex network body ECU)) |
| Automatic Dimming of Display (Controls display dimming control.) |
|
Automatically performs display dimming control when tail mode is not canceled (when the light sensor illuminance signal value is less than the display dimming value, the interior displays and indicators are dimmed). | Nothing | U0155 (Main body ECU (multiplex network body ECU)) |
| Trunk Opener (Performs trunk open control [receives trunk open requests].) |
|
Prohibits opening the trunk. | Recognition not possible. |
(Main body ECU [multiplex network body ECU]) |
| Illumination (Performs illumination control.) |
|
|
The dome light does not turn off immediately after exiting the vehicle. |
(Main body ECU (multiplex network body ECU)) |
| Equipment Related (Controls gateway between the BERKES equipment and CAN.) |
|
|
The remote starter function does not operate. |
(Main body ECU [multiplex network body ECU]) |
| Seat and Mirror Control (Controls the memory function [the seat, steering wheel and mirror position adjustments].) |
|
|
Nothing |
(Main body ECU (multiplex network body ECU)) |
| Diagnostic/C-BEST (Diagnostic phase 4 communication.) |
|
Exits diagnostic mode. | Nothing | - |
| Entry and Start Function/Wireless (Controls entry and start function/wireless functions.) |
|
Entry lock/unlock control not possible. | Nothing | U0327 (Main body ECU (multiplex network body ECU)) |
| Lighting Control (Controls the daytime running lights.) |
|
Daytime running light control is not performed. | Nothing | U0100 (Main body ECU [multiplex network body ECU]) |
| VAST |
|
|
Nothing |
(Main body ECU [multiplex network body ECU]) |
| TPMS (Monitors the tire pressure and meter speed, etc. and operates the meter indicators and multi-information display.) |
|
Sends an initial communication value to the BERKES. | The tire pressure monitor sensor indicator in the combination meter assembly blinks for 1 minute and then stays illuminated. | U0155 (Main body ECU (multiplex network body ECU)) |
| Entry Beam (Detects oncoming traffic, vehicles ahead, street lights, etc. using an onboard sensor and automatically turns the high beam lights on and off.) |
|
The system does not operate (the indicator in the meter blinks). | The indicator in the meter blinks. |
(Main body ECU [multiplex network body ECU]) |
| Microcomputer Preset Steering
|
|
Nothing | The memory, recall, auto-return, auto-away and manual functions do not operate. |
[Multiplex tilt and telescopic ECU] |
| Microcomputer Preset Driving Position System
|
|
|
|
- |
| Microcomputer Preset Position System (Controls the memory of the seat position according to vehicle information [engine switch condition, shift position, door status and vehicle speed] and switch information [memory switch] (Control changes according to transmission information (AT/MT)). |
|
Memory Control does not operate. | Memory Control does not operate. | - |
| Light Control (Controls the illumination of the lights based on courtesy switch information and interior light information.) |
|
|
|
U0142 (Front multiplex network door ECU LH, Front multiplex network door ECU RH) |
| Mirror Operation Control (Controls the operation of the outer mirrors based on mirror switch information from the BDB.) |
|
The mirrors do not operate manually. | The mirrors do not operate manually. | U0142 (Front multiplex network door ECU LH, Front multiplex network door ECU RH) |
| Mirror Heater Control (Controls the operation of the outer mirror heaters based on defogger switch information from the ACN.) |
|
The mirror heaters do not operate. | The mirror heaters do not operate. | U0142 (Front multiplex network door ECU LH, Front multiplex network door ECU RH) |
| Controls the electronic retraction operation of the outer mirrors based on mirror switch information from the BDB. |
|
The electronic mirror retraction function does not operate. | The electronic mirror retraction function does not operate. | - |
| Mirror Reverse Control (Controls the reverse operation of the outer mirrors based on reverse request information from the BDB.) |
|
The mirror reverse-linked operation does not operate. | The mirror reverse-linked operation does not operate. | - |
| Mirror Memorization and Recall Control (Memorizes and recalls the mirror position of the outer mirrors based on the memory request from the BDB.) |
|
|
|
- |
| Memory Switch Signal Substitute Transmission (Transmits the memory switch signal via CAN communication.) |
|
Nothing | The seat and mirror position memorization and recall functions do not operate. | - |
| Leveling (Adjust the vertical beam axis direction of the headlights according to the pitch angle calculated using the wheel speeds and vehicle height sensor value.) |
|
Leveling control stops (beam axis position is stopped at position when malfunction was detected). | Nothing |
(Headlight light control ECU sub-assembly LH) |
| Leveling Indicator (Monitors leveling system malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter.) |
|
Maintains the leveling indicator state. | Nothing | - |
| Destination Determination
|
|
Nothing | Nothing |
(Headlight light control ECU sub-assembly LH) |
| Cornering Light (Turns the cornering light on and off according to the wheel speed, turn, steering angle and shift position data.) |
|
Stops cornering light control (cornering light turns off). | Nothing |
(Headlight light control ECU sub-assembly LH) |
| Low Beam, High Beam, DRL (Domestic Default), Clearance, Side Marker (OPT) (Turns the specified light source on and off according to low beam, high beam, DRL [domestic default], clearance light and side marker light command data.) |
|
Forces the low beams, clearance lights and side marker lights to illuminate. | Nothing |
(Headlight light control ECU sub-assembly LH) |
| LED Headlight Indicator (Monitors low beam LED malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter.) |
|
Maintains the LED headlight indicator status. | Nothing |
[Headlight light control ECU sub-assembly LH] |
| Headlight Cleaner Signal Output (Outputs the headlight cleaner relay ON signal based on the direct line front washer switch signals, headlight cleaner switch signals, low beam illumination command from the main body ECU [multiplex network body ECU] and IG data.) |
|
Stops headlight cleaner operation. | Nothing | U0142 (Headlight light control ECU sub-assembly LH) |
| Automatic High Beam (High beam lights controlled based on wheel speed, steering, shift position and camera data.) |
|
Sets headlight to Lo beam status. Other control (aCOL / Full AFSE Mode, etc.) stopped. |
Nothing |
(Headlight light control ECU sub-assembly LH) |
| AHB indicator (Monitors AHB system malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter.) |
|
Maintains the AHB indicator state. | Nothing |
[Headlight light control ECU sub-assembly LH] |
| Swivel (Estimates the turning radius based on the wheel speed and steering angle, and turns the headlights according to the turning radius.) |
|
Headlights turned to straight ahead position. | Nothing |
(Headlight light control ECU sub-assembly LH) |
| Dynamic Radar Cruise Control (Accelerates or decelerates the vehicle to maintain the distance to the vehicle ahead.) |
|
Radar cruise control is canceled. | Displays a warning message (when cruise control switch is on). |
(Driving support ECU assembly) |
| Pre-crash Safety System (Controls brakes immediately before a collision.) |
|
Pre-crash safety control is stopped. | Pre-crash safety indicator blinks and warning message displays (pre-crash safety cancel switch is off). |
(Driving support ECU assembly) |
| Clearance Sonar Customize (Changes the clearance sonar settings when the user operates the display.) |
|
Nothing | Nothing | - |
| Shift Position Judgment (Receives shift position data which it uses for the clearance sonar detection operation conditions.) |
|
Changes to an operation state which is used when the shift lever is in P. | Nothing | U0101 (Clearance warning ECU assembly) |
| Vehicle Speed Determination (Receives vehicle speed data which it uses for the clearance sonar detection operation conditions.) |
|
Changes to an operation state which is used when the vehicle speed is 20 km/h (12.4 mph) or higher. | Nothing | U0155 (Clearance warning ECU assembly) |
| Vehicle Local Time Synchronization (Receives the vehicle local time and uses it for synchronizing the local time of the clearance sonar.) |
|
Continues an independent count. | Nothing | - |
| TC DTC Output Service (While TC = ON is being received from the ECM, a DTC is output in response to the request from the combination meter assembly.) |
|
If the TC signal is lost during TC service (TC = ON), the TC is determined to be OFF and TC service ends. | Nothing | - |
| Timestamp (Records DTCs and timestamps received from the main body ECU.) |
|
Changes to a separate count inside the ECU and sets separate count recognition information when it receives a fail value or communication stops. | Nothing | - |
| Collision Detection Signal (Notifies the system of a collision in order to perform fuel cut when a vehicle collision occurs.) |
|
Nothing | Nothing | - |
| Passenger Side Air Conditioning Control (Sends information about the passenger in order to control the passenger side air conditioning according to whether there is a passenger in the passenger side seat.) |
|
Nothing | Nothing | - |
| Trigger Signal/Autonomous Transmission (Outputs the yaw rate sensor signal.) |
|
The yaw rate and acceleration sensor (yaw rate sensor) information signal is sent at regular intervals every 0.012 seconds. | Nothing | - |
| Event Data Recorder (EDR) (Records conditions, such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
|
|
Nothing | - |
| Blind Spot Detection (Warns the driver when the system detects a vehicle in the blind spot of an outer mirror.) |
|
A DTC is stored and the blind spot monitor is disabled. | A warning is displayed on the multi-information display. |
(Blind spot monitor sensor RH) |
| Power Trunk Lid Automatic Open/Close Function (Automatically opens the trunk according to the trunk opener switch and operation conditions [engine switch state, shift position, STP, parking brake state and vehicle speed]. Automatically closes the trunk using the power trunk lid close switch.) |
|
|
|
- |
| Trunk Lid Opener Function (Opens the trunk according to the trunk opener switch and operation conditions [engine switch state, shift position, STP, parking brake state and vehicle speed.]) |
|
The trunk opener function does not operate. | The trunk opener function does not operate. | - |
| Luggage Compartment Closer Function (Completely closes the trunk when it is ajar.) |
|
The function cannot reverse operation during the closer operation. | The function cannot reverse operation during the closer operation. | - |
| Courtesy Switch Signal Substitution Output Function (Sends a back door/luggage courtesy switch signal through the CAN bus.) |
|
Nothing | When the luggage compartment door opens, the indicator in the meter indicating the door is open does not illuminate (the BDB recomposes the signal and sends it to the MET). | - |
|
|
|
|
(Forward recognition camera) |
| Automatic High Beam System (Function that recognizes lights in front of the vehicle and automatically operates the high beams.) |
|
The previous values are maintained. | Displays malfunction information on the multi-information display. |
(Forward recognition camera) |
| RSA (Recognizes road signs and displays them on the meter to inform the driver.) |
|
System stops. |
|
(Forward recognition camera) |
| Pre-crash Safety (Function that recognizes vehicles and pedestrians and operates the brake.) |
|
Initializes the recognition processing result and sends it to the driving support ECU (unrecognized condition). |
|
(Forward recognition camera) |
| Speedmeter (Speedometer display) |
|
Only "0" is displayed (no units displayed). | Nothing | - |
| Tachometer (Tachometer display) |
|
Engine speed display set to 0 rpm. | Nothing | U0100 (Combination meter mirror ECU) |
| Shift Display (Shift position display) |
|
Shift position not displayed. | Nothing | - |
| Eco Drive Indicator (Eco gauge display) |
|
Display status set to "Excluded". | Nothing | - |
| Speed Limit (RSA) (Signs recognized by camera) |
|
Signs not displayed. | Nothing | - |
| Speed Limit (Navigation Info) Speed signs displayed by according to Navigation system |
|
Maintains the previous state. | Nothing | - |
| Pre-crash Safety System (Pre-crash safety system display) |
|
Maintains the previous state. | Nothing | U1104 (Combination meter mirror ECU) |
| Cruise Control System (Cruise Control System display) |
|
Cruise Control System not displayed. | Nothing | - |
| Lane Departure Alert System (Lane recognition display) |
|
White lines not displayed. | Nothing | U023A (Combination meter mirror ECU) |
| Audio Feedback (Audio operation display) |
|
Maintains the previous state. | Nothing | - |
| Turn-by-turn Display (Displays arrows in the direction of travel) |
|
Arrows in the direction of travel not displayed. | Nothing | B150A (Combination meter mirror ECU) |
| Lane Information Display (Lane display) |
|
Lane information not displayed. | Nothing | - |
| Eco Area Indicator (Eco area display toggle) |
|
Maintains the previous state. | Nothing | - |
| Display ON/OFF Customize (Screen display ON/OFF configuration) |
|
Maintains the previous state. | Nothing | - |
| SIL Indicator (Gearshift indicator display) |
|
Gearshift indicator not displayed. | Nothing | - |
| Seat Memory-linked (HUD display position control (Automatic)) |
|
Controlled as "No Request". | Nothing | - |
| Destination determination (Destination package determination) |
|
Maintains the previous state. | Nothing | U0142 (Combination meter mirror ECU) |
| ASC System (Outputs simulated engine sounds in accordance with vehicle driving condition.) |
|
|
Simulated engine sound output is stopped. |
(Stereo component equalizer assembly) |
| Torque Vectoring Differential System (Distributes drive force to the right and left wheels.) |
|
Torque vectoring differential function is prohibited. | Displays messages on the multi-information display. |
(Torque vectoring differential ECU assembly) |
| Torque Vectoring Differential System Operation Permission/Prohibition Judgment |
|
Torque vectoring differential function is prohibited. | Displays messages on the multi-information display. | U1172 (Torque vectoring differential ECU assembly) |
| Torque Vectoring Differential System Mode and Drive Force Meter Display |
|
Torque vectoring differential system mode and drive force meter display is not displayed on the multi-information display. | Torque vectoring differential system mode and drive force meter display is not displayed on the multi-information display. | - |