NAVIGATION SYSTEM, Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

In addition, the multi-media module receiver assembly detects a malfunction via the stereo component amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit

  • Harness or connector

  • Speaker

  • Stereo component amplifier assembly

  • Telematics transceiver*

*: w/ Telematics Transceiver

WIRING DIAGRAM

B002ETUE02
B002DHGE01
B002DS7E01
B002DHPE01

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click here

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      DTC B15C3 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  3. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 12 Speakers A
      for 17 Speakers B

    B

    CHECK HARNESS AND CONNECTOR Click here

    A

  4. CHECK HARNESS AND CONNECTOR


    • *1: for RH Side

    • *2: for LH Side


    1. Disconnect the T32 stereo component amplifier assembly connector.

    2. Disconnect the N1*1 and/or O1*2 front No. 1 speaker assembly connector.

    3. Disconnect the K72*1 and/or K17*2 front No. 2 speaker assembly connector.

    4. Disconnect the K51 front No. 3 speaker assembly connector.

    5. Disconnect the P5*1 and/or Q5*2 rear speaker assembly connector.

    6. Disconnect the P4*1 and/or Q4*2 rear No. 2 speaker assembly connector.

    7. Disconnect the T21 rear No. 3 speaker assembly connector.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH Side
      Tester Connection Condition Specified Condition
      T32-13 (FR+) - K72-2 (+) Always Below 1 Ω
      T32-28 (FR-) - K72-1 (-) Always Below 1 Ω
      T32-5 (WFR+) - N1-1 Always Below 1 Ω
      T32-20 (WFR-) - N1-2 Always Below 1 Ω
      T32-15 (RR+) - P4-3 (+TW) Always Below 1 Ω
      T32-30 (RR-) - P4-1 (-TW) Always Below 1 Ω
      P4-4 (+) - P5-1 Always Below 1 Ω
      P4-2 (-) - P5-2 Always Below 1 Ω
      T32-13 (FR+) - Body ground Always 10 kΩ or higher
      T32-28 (FR-) - Body ground Always 10 kΩ or higher
      T32-5 (WFR+) - Body ground Always 10 kΩ or higher
      T32-20 (WFR-) - Body ground Always 10 kΩ or higher
      T32-15 (RR+) - Body ground Always 10 kΩ or higher
      T32-30 (RR-) - Body ground Always 10 kΩ or higher
      P4-4 (+) - Body ground Always 10 kΩ or higher
      P4-2 (-) - Body ground Always 10 kΩ or higher
      for LH Side:
      Tester Connection Condition Specified Condition
      T32-12 (FL+) - K17-2 (+) Always Below 1 Ω
      T32-27 (FL-) - K17-1 (-) Always Below 1 Ω
      T32-4 (WFL+) - O1-1 Always Below 1 Ω
      T32-19 (WFL-) - O1-2 Always Below 1 Ω
      T32-14 (RL+) - Q4-3 (+TW) Always Below 1 Ω
      T32-29 (RL-) - Q4-1 (-TW) Always Below 1 Ω
      Q4-4 (+) - Q5-1 Always Below 1 Ω
      Q4-2 (-) - Q5-2 Always Below 1 Ω
      T32-12 (FL+) - Body ground Always 10 kΩ or higher
      T32-27 (FL-) - Body ground Always 10 kΩ or higher
      T32-4 (WFL+) - Body ground Always 10 kΩ or higher
      T32-19 (WFL-) - Body ground Always 10 kΩ or higher
      T32-14 (RL+) - Body ground Always 10 kΩ or higher
      T32-29 (RL-) - Body ground Always 10 kΩ or higher
      Q4-4 (+) - Body ground Always 10 kΩ or higher
      Q4-2 (-) - Body ground Always 10 kΩ or higher
      for Center Side:
      Tester Connection Condition Specified Condition
      T32-7 (CTR+) - K51-2 (+) Always Below 1 Ω
      T32-22 (CTR-) - K51-1 (-) Always Below 1 Ω
      T32-6 (WF1+) - T21-1 Always Below 1 Ω
      T32-21 (WF1-) - T21-2 Always Below 1 Ω
      T32-7 (CTR+) - Body ground Always 10 kΩ or higher
      T32-22 (CTR-) - Body ground Always 10 kΩ or higher
      T32-6 (WF1+) - Body ground Always 10 kΩ or higher
      T32-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  6. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  7. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  8. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

    OK

  9. CHECK FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or normally functioning one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

  10. CHECK REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or normally functioning one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  11. CHECK HARNESS AND CONNECTOR


    • *1: for RH Side

    • *2: for LH Side

    • *3: w/ Telematics Transceiver


    1. Disconnect the T32 stereo component amplifier assembly connector.

    2. Disconnect the N1*1 and/or O1*2 front No. 1 speaker assembly connector.

    3. Disconnect the K72*1 and/or K17*2 front No. 2 speaker assembly connector.

    4. Disconnect the K51 front No. 3 speaker assembly connector.

    5. Disconnect the P5*1 and/or Q5*2 rear speaker assembly connector.

    6. Disconnect the P4*1 and/or Q4*2 rear No. 2 speaker assembly connector.

    7. Disconnect the T21 rear No. 3 speaker assembly connector.

    8. Disconnect the T22*1 and/or U22*2 rear header speaker assembly connector.

    9. Disconnect the K70 telematics transceiver connector.*3

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH Side (w/o Telematics Transceiver)
      Tester Connection Condition Specified Condition
      T32-13 (FR+) - K70-2 (SPI+) Always Below 1 Ω
      T32-28 (FR-) - K70-3 (SPI-) Always Below 1 Ω
      K70-5 (SPO+) - K72-2 (+) Always Below 1 Ω
      K70-6 (SPO-) - K72-1 (-) Always Below 1 Ω
      T32-5 (WFR+) - N1-1 Always Below 1 Ω
      T32-20 (WFR-) - N1-2 Always Below 1 Ω
      T32-15 (RR+) - P4-3 (+TW) Always Below 1 Ω
      T32-30 (RR-) - P4-1 (-TW) Always Below 1 Ω
      P4-4 (+) - P5-1 Always Below 1 Ω
      P4-2 (-) - P5-2 Always Below 1 Ω
      T32-11 (SR+) - T22-2 (+) Always Below 1 Ω
      T32-26 (SR-) - T22-1 (-) Always Below 1 Ω
      T32-13 (FR+) - Body ground Always 10 kΩ or higher
      T32-28 (FR-) - Body ground Always 10 kΩ or higher
      K70-5 (SPO+) - Body ground Always 10 kΩ or higher
      K70-6 (SPO-) - Body ground Always 10 kΩ or higher
      T32-5 (WFR+) - Body ground Always 10 kΩ or higher
      T32-20 (WFR-) - Body ground Always 10 kΩ or higher
      T32-15 (RR+) - Body ground Always 10 kΩ or higher
      T32-30 (RR-) - Body ground Always 10 kΩ or higher
      P4-4 (+) - Body ground Always 10 kΩ or higher
      P4-2 (-) - Body ground Always 10 kΩ or higher
      T32-11 (SR+) - Body ground Always 10 kΩ or higher
      T32-26 (SR-) - Body ground Always 10 kΩ or higher
      for RH Side (w/o Telematics Transceiver):
      Tester Connection Condition Specified Condition
      T32-13 (FR+) - K72-2 (+) Always Below 1 Ω
      T32-28 (FR-) - K72-1 (-) Always Below 1 Ω
      T32-5 (WFR+) - N1-1 Always Below 1 Ω
      T32-20 (WFR-) - N1-2 Always Below 1 Ω
      T32-15 (RR+) - P4-3 (+TW) Always Below 1 Ω
      T32-30 (RR-) - P4-1 (-TW) Always Below 1 Ω
      P4-4 (+) - P5-1 Always Below 1 Ω
      P4-2 (-) - P5-2 Always Below 1 Ω
      T32-11 (SR+) - T22-2 (+) Always Below 1 Ω
      T32-26 (SR-) - T22-1 (-) Always Below 1 Ω
      T32-13 (FR+) - Body ground Always 10 kΩ or higher
      T32-28 (FR-) - Body ground Always 10 kΩ or higher
      T32-5 (WFR+) - Body ground Always 10 kΩ or higher
      T32-20 (WFR-) - Body ground Always 10 kΩ or higher
      T32-15 (RR+) - Body ground Always 10 kΩ or higher
      T32-30 (RR-) - Body ground Always 10 kΩ or higher
      P4-4 (+) - Body ground Always 10 kΩ or higher
      P4-2 (-) - Body ground Always 10 kΩ or higher
      T32-11 (SR+) - Body ground Always 10 kΩ or higher
      T32-26 (SR-) - Body ground Always 10 kΩ or higher
      for LH Side:
      Tester Connection Condition Specified Condition
      T32-12 (FL+) - K17-2 (+) Always Below 1 Ω
      T32-27 (FL-) - K17-1 (-) Always Below 1 Ω
      T32-4 (WFL+) - O1-1 Always Below 1 Ω
      T32-19 (WFL-) - O1-2 Always Below 1 Ω
      T32-14 (RL+) - Q4-3 (+TW) Always Below 1 Ω
      T32-29 (RL-) - Q4-1 (-TW) Always Below 1 Ω
      Q4-4 (+) - Q5-1 Always Below 1 Ω
      Q4-2 (-) - Q5-2 Always Below 1 Ω
      T32-10 (SL+) - U22-2 (+) Always Below 1 Ω
      T32-25 (SL-) - U22-1 (-) Always Below 1 Ω
      T32-12 (FL+) - Body ground Always 10 kΩ or higher
      T32-27 (FL-) - Body ground Always 10 kΩ or higher
      T32-4 (WFL+) - Body ground Always 10 kΩ or higher
      T32-19 (WFL-) - Body ground Always 10 kΩ or higher
      T32-14 (RL+) - Body ground Always 10 kΩ or higher
      T32-29 (RL-) - Body ground Always 10 kΩ or higher
      Q4-4 (+) - Body ground Always 10 kΩ or higher
      Q4-2 (-) - Body ground Always 10 kΩ or higher
      T32-10 (SL+) - Body ground Always 10 kΩ or higher
      T32-25 (SL-) - Body ground Always 10 kΩ or higher
      for Center Side:
      Tester Connection Condition Specified Condition
      T32-7 (CTR+) - K51-2 (+) Always Below 1 Ω
      T32-22 (CTR-) - K51-1 (-) Always Below 1 Ω
      T32-6 (WF1+) - T21-1 Always Below 1 Ω
      T32-21 (WF1-) - T21-2 Always Below 1 Ω
      T32-7 (CTR+) - Body ground Always 10 kΩ or higher
      T32-22 (CTR-) - Body ground Always 10 kΩ or higher
      T32-6 (WF1+) - Body ground Always 10 kΩ or higher
      T32-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  13. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  14. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  15. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

    OK

  16. CHECK FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or normally functioning one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

  17. CHECK REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or normally functioning one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

  18. CHECK REAR HEADER SPEAKER ASSEMBLY


    1. Replace the rear header speaker assembly with a new or normally functioning one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG (w/Telematics Transceiver)
      NG (w/o Telematics Transceiver)

    OK

    END (REAR HEADER SPEAKER ASSEMBLY IS DEFECTIVE)

    NG (w/o Telematics Transceiver)

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

    NG (w/Telematics Transceiver)

  19. CHECK TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here