STEERING COLUMN ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY

   
   
   1. 

      *a

      Matchmark

      Connect the steering sliding yoke with shaft sub-assembly to the No. 2 steering intermediate shaft assembly.

      Note

      Align the matchmarks on the steering sliding yoke with shaft sub-assembly and No. 2 steering intermediate shaft assembly.

   2. Temporarily install the bolt.

2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

3. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

   
   

   1. 

      *a

      Matchmark

      Install the steering sliding yoke with shaft sub-assembly with No. 2 steering intermediate shaft assembly to the power steering link assembly.

      Note

      Align the matchmarks on the steering sliding yoke with shaft sub-assembly and power steering link assembly.

   2. 

      Install the bolt.

      Torque:

      35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

   3. Tighten the clamp.

4. INSTALL STEERING COLUMN ASSEMBLY

   
   

   1. 

      *a

      Matchmark

      Install the steering column assembly to the No. 2 steering intermediate shaft assembly.

      Note

      Align the matchmarks on the steering column assembly and No. 2 steering intermediate shaft assembly.

   2. Install the steering column assembly with the 4 nuts.

      Torque:

      25.5 N*m  { 260 kgf*cm, 19 ft.*lbf }

   3. 

      Install the bolt.

      Torque:

      35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

   4. Install the brake pedal return spring to the push rod pin and steering column assembly.

   5. Connect each connector and engage each wire harness clamp to the steering column assembly.

   6. 

      Fully tighten the bolt.

      Torque:

      35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

5. INSTALL FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

   Click here

6. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for LHD)

   
   

   1. Install the No. 1 air duct sub-assembly with the clip.

7. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)

   
   

   1. Install the No. 1 air duct sub-assembly with the clip.

8. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

   Click here

9. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

   Note

   
   

   • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

   • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

   • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

   
   

   1. 

      Install in this Direction

      Engage the claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

   2. Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

10. INSTALL STEERING COLUMN COVER

    
    

    1. 

       Install in this Direction

       Engage the claw and guides to install the steering column cover (upper).

    2. 

       Install in this Direction

       Engage the clips and guides to install the meter hood spacer to the steering column cover (upper).

    3. 

       Install in this Direction

       Engage the guides and claws to install the steering column cover (lower).

    4. Install the 3 screws.

11. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

12. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

13. INSTALL STEERING WHEEL ASSEMBLY

    Click here

14. CHECK STEERING WHEEL CENTER POINT

15. INSTALL HORN BUTTON ASSEMBLY

    Click here

16. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

    
    

    1. Reset the auto tilt away function setting to the previous condition by changing the customize parameter.

       Click here

17. ADJUST PARKING ASSIST MONITOR SYSTEM

    Click here