VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1417

DTC Code DTC Name
C1417 High Power Supply Voltage Malfunction

DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is cleared when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1417 High Power Supply Voltage Malfunction

Either of the following is detected:


  • The +BS terminal voltage is 17.4 V or more for 0.8 seconds or more.

  • When voltage at terminal +BS is 17.4 V or higher, power supply voltage of master cylinder pressure sensor is cut for 0.2 seconds or more.

  • Battery

  • Charging system

  • Skid control ECU (Brake actuator assembly)

  • Wire harness or connector

  • ABS NO. 1 fuse

 -
C1417 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The +BS terminal voltage is 17.4 V or more ○ -
When voltage at terminal +BS is 17.4 V or higher, power supply voltage of master cylinder pressure sensor is cut - ○
Detection Time 0.8 seconds or more. 0.2 seconds or more.
Number of Trips 1 trip 1 trip

Tech Tips

DTC will be output when conditions for either of the patterns in th

WIRING DIAGRAM

B002CSJE22

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK BATTERY


    1. Check the battery voltage.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Battery Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY Click here

    OK

  2. CHECK TERMINAL VOLTAGE (+BS TERMINAL)


    1. Turn the engine switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. B002CETC83
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Disconnect the A52 skid control ECU (brake actuator assembly) connector.

    4. Turn the engine switch on (IG).

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A52-38 (+BS) - Body ground Always 11 to 14 V
      A52-38 (+BS) -A52-25 (GND1) Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

    OK

  3. RECONFIRM DTC


    1. Reconnect the A52 skid control ECU (brake actuator assembly) connector.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    3. Turn the engine switch off.

    4. Start the engine.

    5. Perform a road test.

    6. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1417 is not output. A
      DTC C1417 is output. (for LHD) B
      DTC C1417 is output. (for RHD) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    C

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here